manualshive.com logo in svg

Ross openGear GPI-100, User Manual, Page: 28 / 42

Share
Download
Ross openGear GPI-100 User Manual Download Page 28

3–4 • User Controls

GPI-100 User Manual (Iss. 06)

PGM VID IN 

(DS3)

Green

When lit green, this LED indicates the Program Video input is 
present and valid.

Red

When lit red, this LED indicates that no valid input is present. 
This typically means that the input cable is disconnected.

PGM VID 

OUT (DS4)

Green

When lit green, this LED indicates the Program Video output 
serializer is locked to a valid input.

Red

When lit red, this LED indicates a hardware fault on the card.

DS5

This LED is not implemented.

DS6

This LED is not implemented.

DS7

This LED is not implemented.

DS8

This LED is not implemented.

VIDEO 

ERROR 

(DS9)

Green

When lit green, this LED indicates no video errors are 
occurring.

Orange

When lit orange, this LED indicates that there has been an error 
(e.g. EDH) in the video input stream.

UKNOWN 

REAR 

MODULE 

(DS10)

Green

When lit green, this LED indicates a supported rear module is 
installed with the card.

Orange

When lit orange, this LED indicates this indicates that the rear 
module connected to the GPI-100 is not one of the types 
recognized by the software. Operation may not be correct.

DS11

This LED is not implemented.

DS12

This LED is not implemented.

Table 3.1  LEDs on the GPI-100

LED

Color

Display and Description

Summary of Contents for openGear GPI-100











































Reviews:

No comments