background image

Setup (Iss. 05) • 14 

Setup

Power Adapter and Supply

Connect the PS-9000 power adapter to the power supply connector. The 
PS-9000 provides up to 2A of reg5V DC (5%). The DC power cord has 
a locking connector that securely fastens into the power supply DC jack on the 
CMA-9011-R. The CMA-9011-R has a standard miniature power jack (center 
pin positive). 

If using an adapter other than the PS-9000, ensure that:

the polarity is correct

the voltage is +5V DC regulated to 5%

sufficient current for the CMA-9011-R is supplied 

Caution

 — Use of improper adapters may damage the CMA-9011-R 

and will void the warranty.

Installations outside of North America using line voltages of 200-240V require a 
plug, certified for the country of use, to be installed on the supplied line cord. 
Refer to the section “

Important Regulatory and Safety Notices to Service 

Personnel

” at the front of this manual for details.

Cable Connections Overview

Connect the cables to the CMA-9011-R according to the designations indicated 
on the chassis label and 

Figure 5

. The input is internally terminated at 75ohm. It 

is not necessary to terminate unused outputs.

Figure 5  

CMA-9011-R Connections

DIP Switch Setup

An 8-position DIP switch allows you to configure the CMA-9011-R to fit into 
almost any installation. (

Figure 6

) Settings are described in 

Table 1

.

POWER

SUPPLY

SDI IN

SDI OUT 2

SDI OUT 4

ANLG CVBS

OUT 2

SDI OUT 1

SDI OUT 3

ANLG CVBS

OUT 1

Summary of Contents for GearLite CMA-9011-R

























Reviews: