Mor-Vision
™
Mirror/Monitor Backup Camera System, Installation User Manual
Mor-Vision
™
Mirror/Monitor Backup Camera System, Installation User Manual
3
4
INSTALLATION INSTRUCTIONS
IMPORTANT
For typical rear-view installation, the rear camera MUST be connected
to the power harness at the connector marked “REVERSE”
NOTE : THE FOLLOWING INSTRUCTIONS ARE FOR TYPICAL REAR-VIEW
APPLICATION.
STSC109B CAMERA
1. Find location for camera close to rear marker lights, centered on vehicle.
Attachment point must be sturdy enough to support camera and bracket.
(Fig. 1)
2. Camera is designed for installation near the top of the vehicle in order to capture
images of the rear bumper and danger zones immediately behind the vehicle.
It is not recommended to be installed near the bumper. This reduces the view of
critical areas and increases the chance of physical damage to the camera.
3. Remove camera cover by removing the screws located at the ends of the camera.
Remove camera by twisting retaining ring counterclockwise until camera is
released. (Fig. 2)
4. Drill one ¾” (16mm) hole where the camera cable will go through the body of
the vehicle. Make sure there are no obstructions behind your hole. (Using the
camera base as a template, drill two 1/8”(3.5mm) holes for attachment screws.
(Fig. 3)
5. Attach camera housing to vehicle with screws provided.
6. Insert camera back into housing and adjust lens angle to desired setting. Note that
the light sensor is the bottom of the camera. Once the angle is set, tighten retaining
ring onto camera. Tighten set screws on the sides of the camera. (Fig. 4)
7. Return top cover and secure with original screws. (Fig. 5)
STSM217 MONITOR
1. Attach mirror/monitor inside vehicle in an existing interior mirror location
(e.g. center of dash, or overhead).
3. Fasten mirror monitor to bracket and adjust mounting angle to allow optimum
driver viewing comfort.
STSH341 CAMERA EXTENSION CABLE
1. Be sure to position the cable properly. The male end attaches to the camera.
The female end attaches to the power/video/audio distribution harness, typically
located under the dashboard.
2. Do not run the cable over sharp edges or corners. Do not kink the cable.
Keep the cable away from hot and rotating parts.
3. Fasten all cable runs, and secure all excess cable. (Fig. 6)
COLOR BACKUP CAMERA SYSTEM, COLOR MIRROR MONITOR
Please read this manual thoroughly. This manual contains instructions to make
the installation of the camera and monitor easier. The mirror/monitor backup
camera system is an upgrade to standard rearview mirror systems, and will provide
additional rearview vision when installed and maintained properly. It is not intended
in any way to be a substitute for careful and cautious driving. All applicable traffic
laws and motor vehicle safety regulations must still be obeyed.
FEATURES
STSC109B CAMERA
• 40,000 pixel image sensor
• 0.5 Lux sensitivity (6 IR-LED)
• Auto white balance (AWB)
• Field of view 150° diagonal
• Automatic electronic iris provides a clearer,
more consistent image in low and bright light
• Compact and lightweight design installs
easily into most vehicles
• Rain/snow proof
CONTENTS OF COMPLETE SYSTEM
STSM217 HIGH BRIGHTNESS
LCD COLOR 7” MONITOR
• Menu button for picture,
system and options
• 2 video channels
• Power/stand-by switch
• Built-in speaker
• Auto-dimming
PART LIST
STSK1030
Power Harness
STSK5465/PHAR
Backup Camera
STSC109B
Extension Harness
STSH341
Fuse Holder
HAR6028 (x2)
Interior
Mirror/Monitor
STSM1030A (includes
Monitor STSM217)
PART LIST
STSK6630
Power Harness
STSK5465/PHAR
Backup camera
STSK109B
Extension Harness
STSH341
Fuse Holder
HAR6028 (x2)
Interior
Mirror/Monitor
STSM630A (includes
Monitor STSM217)
PART LIST
STSK5530
Power Harness
STSK5465/PHAR
Backup Camera
STSK109B
Extension Harness
STSH341
Fuse Holder
HAR6028 (x2)
Interior
Mirror/Monitor
STSM530A (includes
Monitor STSM217)
