Roofit.Solar ClicSeam Safety And Installation Manual Download Page 22 | Manualshive

Page: 22 / 25

background image

ClicSeam™ Safety and Installation Manual

22

ClicSeam™ panel connection using

installation plate

Installation plate is needed when according to the roof plan the column should start from regular metal

1. ClicSeam™ Eaves flashing

2. ClicSeam™ Installation
plate 700 mm, end-bent
3. ClicSeam™ PV-panel

Cross-section

showing Installation plate and PV-panel with Edge panel removed

ClicSeam™ installation plates are
intstalled in rows according to
the system plan, starting with the
edge panel.

Note that fastening clips are to
be mounted in each batten and
that screws and ClicSeam™  top
profile have to be installed
according to ClicSeam™  panel
connection.

The installation plates are
installed by sliding the end-bent
side under the eaves flashing.

The connection between  the
installation  plate and eaves
flashing does not require silicone
sealant.

Min 200 mm
overlap between
the installation
plate and PV-panel

2

3

1

«
...
20
21
22
23
24
...
»

Summary of Contents for ClicSeam


























Reviews:

No comments

Related manuals for ClicSeam

Brand: Bematech Pages: 18

Brand: IEI Technology Pages: 132

Enecom HF135-6-16

Brand: En-Eco Pages: 20

Brand: Computer Dynamics Pages: 40

Brand: AXIOMTEK Pages: 68

Brand: Risecom Pages: 36

091-55-194B-24-20A

Brand: KUSSMAUL Pages: 6

Brand: Evergreen Solar Pages: 4

Brand: SolarWorld Pages: 2

Brand: Honeywell Pages: 16

Brand: IEI Technology Pages: 112

Brand: IEI Technology Pages: 160

Brand: Christ Pages: 32

BiHiKu6 Mono CS6Y-550MB-AG

Brand: Canadian Solar Pages: 98

Brand: IEI Technology Pages: 137

S19A/S24A-QM87i

Brand: IEI Technology Pages: 136

Brand: IEI Technology Pages: 137

Brand: IEI Technology Pages: 151

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands