background image

21 GAUGE 12.9MM CROWN STAPLER

4

WARNING!

8) Connect a proper connector to this tool correctly. 
The connector for this tool should never have pressure kept when air 
supply is cut off. If an improper part is applied, then the tool can operate 
due to pressure left within it even after the airline is disconnected 

possibly resulting in injury. 

9) Disconnect the air line and empty the fasteners out of the container in 
case that the tool is not used.
Be sure to cut off air supply and empty the fastener container when the 
work is completed or when you move to another workshop, maintain, 

disassemble, or repair this tool, or clear jam. Make sure that the airline 

is disconnected in loading the container with fasteners again.

CAUTION:

10) Make sure that each fastener is locked tightly.
The tool can be damaged if you use it with each fastener loosened, or 
screws or bolts assembled wrongly. Make sure that all screws and bolts 
are assembled correctly and tightly before using the tool. 
11) Never let a worker remove or manipulate a safety device, or 
recompose the tool at his or her discretion. 
If you remove a safety device, or manipulate or recompose the tool at 
will, it can cause a drop in performance and breakdown of the tool and 

result in injury due to mechanical trouble and malfunction. 

12) Be sure to disconnect the air line and empty fasteners out of the 
container if the tool is not used. 
You must disconnect the air line and empty the fastener container when 
the work  is completed or suspended, when you go out of a workshop, 
when you move or transfer the tool, or on other occasions. 
13) Stick the muzzle correctly to the target plane for drive a fastener. 
If correct drive a fastener is not implemented on the target plane, the 

fired fastener can spring out, possibly resulting in injury. 

14) You are prohibited from using the tool for other purposes than drive 
a fastener and from throwing or dropping it. 

Summary of Contents for RA-8016














Reviews: