manualshive.com logo in svg

RollSeal RS-500 Series, Installation Manual

Share
Download
RollSeal RS-500 Series Installation Manual Download Page 24

 

 

Page 24 

RS-500/600 Series Doors 

 Part No 4801-5154 Rev 01-2017 

14

 

Manaras Motor Mounting to RS-500/600 Series Doors 

 

Warning! 

Prior to mounting the Manaras it is important that you read all the information contained within 

this document and the Manaras Installation and Instruction Manual provided with the door. 

Failure to do so could result in severe personnel injury or damage to equipment! 

 
For more detailed information on mounting, wiring and operating the Manaras, refer to the Manaras Installation and 
Instruction Manual provided with the door. 

Sprockets are mounted as follows on RS-500/600 Series Doors: 

Size 50-12 (small) goes on the door. Size 50-23 (large) goes on the motor. See drawing below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

NOTE: Manaras GH Operator can be mounted in its normal upright position for all options.  However it 

may be necessary to remove and re-install the chain and pulley on the opposite side to prevent chain 
interference. Refer to Manaras Opera GH Installation & Instruction Manual if your operator is a 
gear head operator. 

 
 

!

!

 

Summary of Contents for RS-500 Series





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands