70
Effects
46: Cho
→
Flanger (Chorus
→
Flanger)
[02H, 0BH]
This effect connects a chorus and a flanger in series.
fig.9-49
Cho Dly (Chorus Pre Delay)
0–100ms [1 (40 03 03)]
Adjusts the time delay from when the direct sound begins
until the chorus sound is heard.
Cho Rate (Chorus Rate)
0.05–10.0 [2 (40 03 04)]
Adjusts the modulation speed of the chorus effect.
Cho Depth (Chorus Depth)
0–127 [3 (40 03 05)]
Adjusts the modulation depth of the chorus effect.
+Cho Bal (Chorus Balance)
100:0–0:100(D:E) [5 (40 03 07)]
Adjusts the volume balance between the direct sound and
the chorus sound. With a setting of D>0E, only the direct
sound will be output. With a setting of D0<E, only the
chorus sound will be output.
“D” and “E” stand for “direct sound” and “effect sound”
respectively.
FL Dly (Flanger Pre Delay Time) 0–100ms [6 (40 03 08)]
Adjusts the time delay from when the direct sound begins
until the flanger sound is heard.
FL Rate (Flanger Rate)
0.05–10.0 [7 (40 03 09)]
Adjusts the modulation speed of the flanger effect.
FL Depth (Flanger Depth)
0–127 [8 (40 03 0A)]
Adjusts the modulation depth of the flanger effect.
FL Fb (Flanger Feedback Level)
-98%–+98% [9 (40 03 0B)]
Adjusts the proportion (%) of the flanger sound that is fed
back into the effect. Negative (-) settings will invert the
phase.
#FL Bal (Flanger Balance)
100:0–0:100(D:E) [10 (40 03 0C)]
Adjusts the volume balance between the sound that passes
through the flanger and the sound that does not. With a
setting of D>0E, only the chorus sound will be output, and
with a setting of D0<E, the chorus sound that passes
through the flanger will be output.
“D” and “E” stand for “direct sound” and “effect sound”
respectively.
Low Gain
-12–+12 [17 (40 03 13)]
Adjusts the low frequency gain.
Hi Gain (High Gain)
-12–+12 [18 (40 03 14)]
Adjusts the high frequency gain.
Level (Output Level)
0–127 [20 (40 03 16)]
Adjusts the output level.
Effects that connect three or more types of
effect in series (series 3/series 4/series 5)
47: Rotary Multi
[03H, 00H]
This connects Overdrive (OD), 3-band equalizer (EQ), and
Rotary (RT) effects in series.
fig.9-50
●
OD (Overdrive)
+OD Drive
0–127 [1 (40 03 03)]
Adjusts the degree of distortion. The volume will change
together with the degree of distortion.
OD Sw (Overdrive Switch)
Off/On [2 (40 03 04)]
Turns the Overdrive effect on/off.
●
EQ (Equalizer)
EQ L Gain (EQ Low Gain)
-12–+12 [3 (40 03 05)]
Adjusts the low range gain of the equalizer.
EQ M Fq (EQ Mid Frequency)
200–6.3k [4 (40 03 06)]
Sets the center frequency for the equalizer mid-range.
EQ M Q (EQ Mid Q)
0.5/1.0/2.0/4.0/9.0 [5 (40 03 07)]
Adjusts the width of the area centered at the EQ M Fq
setting in which the gain will be affected. The area affected
will become narrower as this value is increased.
EQ M Gain (EQ Mid Gain)
-12–+12 [6 (40 03 08)]
Adjusts the gain of the area specified by the EQ M Fq
parameter and the EQ M Q parameter.
EQ H Gain (EQ High Gain)
-12–+12 [7 (40 03 09)]
Adjusts the high-range gain of the equalizer.
●
RT (Rotary)
RT L Slow (RT Low Frequency Slow Rate)
0.05–10.0 [8 (40 03 0A)]
Adjusts the speed of the low-range rotor for the slow-speed
setting.
RT L Fast (RT Low Frequency Fast Rate)
0.05–10.0 [9 (40 03 0B)]
Adjusts the speed of the low-range rotor for the fast-speed
setting.
RT Lo Accl (RT Low Frequency Acceleration)
0–15 [10 (40 03 0C)]
Adjusts the time over which the rotation speed of the low-
range rotor will change from slow-speed to fast-speed (or
fast-speed to slow-speed) rotation. Smaller values will
require greater time to reach the new rotational speed.
RT Lo Lev (RT Low Frequency Level)
0–127 [11 (40 03 0D)]
Adjusts the volume of the low-range rotor.
L
R
Flanger
EQ
EQ
Chorus
L
R
Rotary
EQ
Over
drive
Summary of Contents for Sound Canvas SC-8820
Page 2: ......
