Roland KIWI-3P Manual Download Page 48

Page: 48 / 60

Table 1.0 Command ID

Data Byte

Data Type
Byte details

7 ------- 0

Data Details

$01 (1) Request Global Dump

No Data

3P transmits a $02 (2) command

$02 (2) Transmit or Receive Global Dump

32 data bytes

$00 (0) = Midi Channel In

000yxxxx

xxxx = 0-15 for midi channel 1-16
y =

set for Omni

$01 (1) = Midi Channel Out

0000xxxx

xxxx = 0-15 for midi channel 1-16

$02 (2) = Seq Midi Channel Out

0000xxxx

xxxx = 0-15 for midi channel 1-16

$03 (3) = Enable MidiCC

000000xx

xx =

00=Off
01=CC Receive Enabled (Default)

10=CC Transmit Enabled
11=CC Receive & Transmit Enabled

$04 (4) = Enable Sysex

0000000x

x =

Off/On (set=On)

$05 (5) = Enable Program Change 000000xx

xx =

00=None

01=PC Receive Enabled (Default)
10=PC Transmit Enabled

11=PC Receive & Transmit Enabled

$06 (6) = Midi Soft Through

000000xx

xx =

00=Stop all
01=Pass all

10=Pass only nonCC
11=Stop only CC we have used

Note - SysEx intended for the Kiwi-3P will not be passed
Note – Active Sensing commands are suppressed within the Kiwi-3P

and are not passed on

$07 (7) = Enable Midi Clock Gen 0000000x

x =

Off/On (set=On)

$08 (8) = Master Clock Source

0000000x

0-Internal
1-Midi

$09 (9) = Master Fine Tune

0xxxxxxx

x =

Master Fine Tune (+- 100 cents)

$0a (10) = Clock Display

0000000x

0-Off

1-On

$0b (11) = Guitar Mode

0000000x

x =

Off/On (set=On) – Note this uses midi channels 1-6 only

$0c (12) = Pedal Control

0000000x

Sets Hold Pedal Polarity

$0d-$1f (13-31) = Nulls

Not Used

$03 (3) Request Tone Edit Buffer Dump

No Data

www.kiwitechnics.com

3P Matrix Upgrade User Manual v1.2

Summary of Contents for KIWI-3P





























































Search results

Summary of Contents for KIWI-3P

Reviews:

Brands by name

Popular brands

Roland KIWI-3P, Manual

Search results

Summary of Contents for KIWI-3P

Reviews:

Brands by name

Popular brands