Roland KIWI-3P Manual Download

Page: 47 / 60

Midi Sysex Data

Notes
$nn = Hexadecimal Data - Decimal data is in Brackets e.g. $0a (10)

Sysex Header

$f0

Sysex Start

$00 $21 $16

Kiwitechnics Manufacturers ID

$60

Kiwitechnics ID

$08

Kiwitechnics 3P Matrix ID

Command ID (see table 1.0)

$01

Request Global Dump

$02

Transmit/Receive Global Dump

$03

Request Tone Edit Buffer Dump

$04

Transmit/Receive Tone Edit Buffer Dump

$05

Request Tone Dump

$06

Transmit/Receive Tone Dump

$09

Request Seq Dump

$0a

Transmit/Receive Seq Dump

$0d

Request Tone Parameter

$0e

Transmit/Receive Tone Parameter

$0f

Request Global Parameter

$10

Transmit/Receive Global Parameter

$13

Request Sequence Edit Buffer Dump

$14

Transmit/Receive Sequence Edit Buffer Dump

Data

Depending on command type (see table 1.0)

$f7

Sysex Footer

WARNING! Sysex dumps have the ability to put non valid settings into memory and few checks are made for validity. If the 3P becomes
unusable due to non valid data you will need to do a full restore of the 3P which will lose all saved memory.

www.kiwitechnics.com

3P Matrix Upgrade User Manual v1.2

Summary of Contents for KIWI-3P





























































Search results

Summary of Contents for KIWI-3P

Reviews:

Related manuals for KIWI-3P

Brands by name

Popular brands

Roland KIWI-3P, Manual

Search results

Summary of Contents for KIWI-3P

Reviews:

Related manuals for KIWI-3P

Brands by name

Popular brands