Roland DU2-54 User Manual Download Page 38

Page: 38 / 42

The Drying-heater Unit Doesn't Get Hot

Is the power cord connected?

Connect the power cord securely.



P.28 "Connecting the Cables"

Is the drying-heater unit cable
connected?

Connect the drying-heater unit cable to the printer unit.



P.28 "Connecting the Cables"

Is [OPTION DRYER] on the printer
set to "ENABLE"?

The drying-heater unit doesn't operate unless this is set
to "ENABLE." Check the settings.



P.32 "What to Do First"

Is the power switch on?

Make sure the power switch is on.



P.33 "Switching the Power On and Off"

Is the temperature of the room
too low?

Use the machine in an environment where the
temperature is 20 to 32˚C (68 to 90˚F).

The Blower-fan Unit Doesn't Run

Is the blower-fan unit cable
connected?

Connect the blower-fan unit cable to the printer unit.



P.28 "Connecting the Cables"

Is [BLOWER FAN] on the printer
set to "ENABLE"?

The blower-fan unit doesn't operate unless this is set to
"ENABLE." Check the settings.



P.34 "Turning On the Power of the Blower-fan Unit"

If a Message Appears

[OPTION DRYER IS NOT
CONNECTED]

The unit is not connected correctly. Switch off the power
to all devices, then check the connections between the
unit and the printer.



P.28 "Connecting the Cables"



P.32 "What to Do First"

What to Do If

Summary of Contents for DU2-54











































Search results

Summary of Contents for DU2-54

Reviews:

Related manuals for DU2-54

Brands by name

Popular brands

Roland DU2-54, User Manual

Search results

Summary of Contents for DU2-54

Reviews:

Related manuals for DU2-54

Brands by name

Popular brands