manualshive.com logo in svg

Roland DU2-54, User Manual

Share
Download
Roland DU2-54 User Manual Download Page 30

28

WARNING

 

Connect to an electrical outlet that complies with this machine's ratings  

   

(for voltage, frequency, and current).

Incorrect voltage or insufficient current may cause fire or electrical shock.

WARNING

 

Connect the machine to ground.

This can prevent fire or electrical shock due to current leakage in the event 

of malfunction.

WARNING

 

 Perform this task with all power switches left switched off.

Failure to observe this instruction may cause the machine to move suddenly, 

resulting in injury.

The printer and the drying-heater unit require separate high-capacity electrical outlets. 

Make sure to connect the two power cords to outlets on separate systems. Also, make sure 

that the electrical outlets meet the machine's ratings.

When VG-640/540 is Used

Connect the drying-heater unit and blower-fan unit cables, and the power cord.

Power Cord

Power-cord connector

Power cord

Electrical outlet

Connecting the Cables

Summary of Contents for DU2-54











































Reviews:

No comments

Brands by name

Popular brands

Load more brands