background image

Roksan Audio ltd

 

 

Xerxes.20 Record Player User Manual 

 

 

General Use 

 

 

Version 3.0 

All specifications are liable to change without notice. E&OE

 

Page 20 of 22

 

ENGLISH

 

If you suspect that your ROKSAN 

Xerxes.20 Record Player

 is not operating properly, first check all the 

connections carefully. Below are some likely encountered problems with suggestions for possible cure. The list is 
not exhaustive: If you have any unresolved problems, please consult your appointed ROKSAN dealer or 
distributor. 
 

SYMPTOM LIKELY 

CAUSE SUGGESTED 

REMEDY 

Platter not turning 
 
 

Motor drive lead not inserted properly 
Motor drive not switched on 
Drive belt not fitted 

Ensure Motor drive lead is fully inserted 
Switch Motor drive on 
Fit drive belt and try again 

Start-up too slow 

(>10sec.)

 

Motor locked in transit position 
Belt dirty or sticky 
 
Main bearing ‘dry’ 
 
 
Main bearing ball missing 

Remove motor transit 
Clean belt with wax based furniture 
polish 
Check, if no damage to bearing, 
recharge with Roksan main bearing oil 

(see above)

 

Check, if no damage to bearing, fit new 
Xerxes.20 main bearing ball 

(if in doubt 

consult your Roksan retailer)

 

Belt falling off 
 
Platter touching the plinth 

Incorrect motor alignment 
 
Incorrect main bearing alignment 

Check and realign motor 

(see above)

 

 
Check and realign bearing 

(see above)

 

 
 
 
 
 
 
 
 
 
 
There are no user-serviceable parts on your 

Xerxes.20 Record Player

. If a fault should develop, refer any 

servicing to your appointed ROKSAN dealer, distributor or approved service agent. 
 
Your ROKSAN 

Xerxes.20 Record Player

 is guaranteed against any defect in materials and workmanship for a 

period of 

two years

 from the date of purchase. 

This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the 
equipment was purchased and returned to ROKSAN within 

28 days

 of purchase. 

This guarantee excludes: 
1.  Damage caused due to accident, misuse, neglect and incorrect installation, adjustment or repair. 
2.  Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised 

distributor for the purposes of repair or inspection. 

 
Carriage costs to ROKSAN shall be borne by the consignor. 
 
All claims under this guarantee must be made through an authorised ROKSAN retailer. 
 
If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification 
ROKSAN reserves the right to make a charge for examination and return carriage. 
 

Unauthorised servicing will void this guarantee. 

 
 
 
 
 
 
 
 

T R O U B L E S H O O T I N G

 

X

X

X

E

E

E

R

R

R

X

X

X

E

E

E

S

S

S

.

.

.

2

2

2

0

0

0

 Record Player

G U A R A N T E E

 

X

X

X

E

E

E

R

R

R

X

X

X

E

E

E

S

S

S

.

.

.

2

2

2

0

0

0

 Record Player

Summary of Contents for Xerxes.20























Reviews: