background image

 
 
 

 

TECHNICAL NOTE

Ambient Light Sensor IC Series 

Digital 16bit Serial Output Type 
Ambient Light Sensor IC

   

BH1715FVC 

 
 

 Descriptions 

BH1715FVC is an digital Ambient Light Sensor IC for I

2

C bus interface. This IC is the most suitable to obtain the ambient 

light data for adjusting LCD and Keypad backlight power of Mobile phone. It is possible to detect wide range at High 
resolution. ( 1 - 65535 lx ). 

 

 Features 

 1) I

2

C bus Interface 

  f / s Mode Support 

 

  2)  Spectral responsibility is approximately human eye response 
  3)  Illuminance to Digital Converter 
  4)  Wide range and High resolution. 

  1 – 65535 lx 

 

  5)  Low Current by power down function 
  6)  50Hz / 60Hz Light noise reject-function 
  7)  1.8V Logic input interface 
  8)  No need any external parts 
  9)  Light source dependency is little. ( ex. Incandescent Lamp. Fluorescent Lamp. Halogen Lamp. White LED. Sun Light ) 
  10)  It is possible to select 2 type of I

2

C slave-address. 

  11)  Adjustable measurement result for influence of optical window ( It is possible to detect min. 0.33 lx, max. 100000 lx by 

using this function. ) 

12) 

Small measurement variation (+/- 15%) 

 

 Applications 

Mobile phone, LCD TV, NOTE PC, Portable game machine, Digital camera, Digital video camera, Car navigation, PDA,   
LCD display 

 

  Absolute Maximum Ratings 

 

Parameter Symbol 

Limits 

Units 

Supply Voltage 

Vmax

 

4.5 V 

Operating Temperature 

Topr 

-40

85 

 

Storage Temperature 

Tstg 

-40

100 

 

SDA Sink Current 

Imax 

mA 

Power Dissipation

 

Pd

 

260

 

mW

 

※ 

70mm  ×  70mm  ×  1.6mm glass epoxy board. Derating in done at 3.47mW/℃  for operating above Ta=25℃. 

 

 Operating Conditions 

 

Parameter Symbol 

Min. 

Typ. 

Max. 

Units 

VCC Voltage 

Vcc 

2.4 

3.0 

3.6 

I

2

C Reference Voltage 

VDVI 

1.65 

 VCC  V 

 
 
 
 
 

                                                                                                       

June 2008 

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Summary of Contents for BH1715FVC

















Reviews: