Rohde & Schwarz R&S AMS32-K31 User Manual Download

Page: 2 / 49

The measurements described in this application note require an OTA Performance Test System
R&S

TS8991, order no. 1149.4309.03, and the following software products:

●

"Over-The-Air (OTA) Performance Measurement Software", R&S

AMS32, stock number 1508.6650.02

●

"Option for R&S

AMS32 OTA Software: LTE SISO", R&S

AMS32-K29, stock number 1508.6680.29

●

"Option for R&S

AMS32 OTA Software: MIMO", R&S

AMS32-K31, stock number 1508.6680.31

© 2012 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Munich, Germany
Phone: +49 89 41 29 - 0
Fax: +49 89 41 29 12 164
E-mail:

[email protected]

Internet:

http://www.rohde-schwarz.com

Printed in Germany – Subject to change – Data without tolerance limits is not binding.
R&S

is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of the owners.

The following abbreviations are used throughout this manual: R&S

is abbreviated as R&S, e.g. R&S AMS32 denotes R&S

AMS32.

Summary of Contents for R&S AMS32-K31


















































Search results

Summary of Contents for R&S AMS32-K31

Reviews:

Related manuals for R&S AMS32-K31

Brands by name

Popular brands

Rohde & Schwarz R&S AMS32-K31, User Manual

Search results

Summary of Contents for R&S AMS32-K31

Reviews:

Related manuals for R&S AMS32-K31

Brands by name

Popular brands