![Rohde & Schwarz 1164.4391.03 Service Manual Download Page 167](http://html1.mh-extra.com/html/rohde-and-schwarz/1164-4391-03/1164-4391-03_service-manual_1477763167.webp)
R&S FSP
Module Replacement
1164.4556.82 3.63
E-1
Replacing Flash Disk A60 (Option R&S FSP-B20)
(See chapter 5, spare parts list, item 1702, and drawings 1164,4391 and 1155.1741.)
The flash disk is located in the instrument between the controller panel and the modules. The spare part
is supplied with pre-installed software.
Opening the Instrument and Removing the Flash Disk
Switch off unit, disconnect it from power supply, unscrew 4 rear-panel feet (450) and pull off
enclosure (410) towards rear.
Unscrew the two countersunk screws (260) at the top of the instrument and the three countersunk
screws (250) at the fan side, lift the cover at the top (240) of the instrument to the left side and take
off.
Disconnect the SATA data cable (721) and the SATA power cable (722) on the flash disk.
Unscrew the two countersunk screws (740) on the flash disk mounting plate (730).
Remove the flash disk (1702) with the mounting plate (730).
Replacing the Compact Flash Board A60
Undo 4 countersunk screws (750), remove compact flash board (1702) and screw the new board to
the mounting plate (730).
Replacing the Flash Memory A61
Unlock and disconnect the flash memory card (1713). Insert the new flash memory card and lock
them in place with the clamp (1730).
Installing the New Flash Disk and Putting into Operation
Using two countersunk screws (740), fasten the flash disk and the disk holder to the instrument.
Note:
The disk holder is plugged into a metal panel at the bottom.
Connect the SATA data cable (721) and the SATA power cable (722) to the flash disk.
Put the top cover (240) on the instrument and fasten it in place with 2 countersunk screws (260) and
3 countersunk screws (250).
Slide on enclosure (410) and screw on 4 rear-panel feet (450).
Connect the AC supply cable and switch on the power switch. The unit is now in the standby mode.
A cold boot is required after replacing the flash disk. See section "Performing a Cold Boot" in this
chapter.
After starting the instrument, make sure that no messages are recorded in the log file:
-
[
SETUP
: SYSTEM INFO : SYSTEM MESSAGES
]
Start the selftest and check the results to make sure that no errors occurred:
-
[
SETUP
: SERVICE : SELFTEST ], then [SELFTEST RESULT]
Start total calibration and check the results:
-
[
CAL
: CAL TOTAL
]
, then
[
CAL RESULTS
]
Perform a firmware update if necessary.
Repeat the total calibration and check the result:
-
[
CAL
: CAL TOTAL ] , then [ CAL RESULTS ]
Summary of Contents for 1164.4391.03
