background image

Important Safety Information

Please review and read the instructions very carefully in order to understand the specification of the equipment. This is

essential information before installing, operating, service or maintaining your equipment. These messages or alerts may appear

throughout this publication and manual for your purchased equipment. The messages are designed to warn you of possible

hazards or to bring to your attention the information that would assist and clarifies steps and procedures.

DANGER

WARNING

CAUTION

CAUTION

NOTICE

DANGER This symbol represents an imminently hazardous situation which, if not avoided, 

will result in death or serious injury. Please follow instructions carefully.

WARNING This symbol represents a potentially hazardous situation which, if not avoided, can 

result in death or serious injury. Please follow instructions carefully.

CAUTION This symbol indicates a potentially hazardous situation which, if not avoided, can 

result in minor or moderate injury.

CAUTION, This symbol is used without the safety alert symbol, indicates a potentially

hazardous situation which, if not avoided, can result in equipment damage. Please follow

instructions carefully. Please follow instructions carefully. 

NOTICE This symbol provides informations and practices not related to physical injury

including certain environmental hazards, potential damage or loss of data. Please follow

instructions carefully.

This is a safety alert symbol. It is used to alert you to potential personal

injury hazards. Please follow the instructions very carefully and obey all

safety messages that follow this symbol to avoid possible injury or death. 

This symbol and label provides Danger or Warning safety which indicates 

an electrical hazard exists. If instructions are not fully followed, it may 

result in personal injury.

Page

 3

Summary of Contents for SolidRack R3100
















Reviews: