7
DRILL PRESS
ENG
aCCESSORIES
Chuck key
1
Allen key
2
We recommend that you purchase your accessories
from the same store that sold you the tool. Use good
quality accessories marked with a well-known brand
name. Choose the type according to the work you
intend to undertake. Refer to the accessory packaging
for further details. Store personnel can assist you and
offer advice.
REaD aLL INSTRuCTIONS bEFORE
uSING ThIS aPPLIaNCE
INSTRuCTIONS PERTaINING TO a RISK OF INJuRy
GENERaL
a. GROuNDING INSTRuCTIONS
1. All grounded, cord-connected tools:
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided – if it will not fit
the outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. The conductor with insulation
having an outer surface that is green with
or without yellow stripes is the equipment-
grounding conductor. If repair or replacement
of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as to
whether the tool is properly grounded.
Use only 3-wire extension cords that have
3-prong grounding plugs and 3-pole receptacles
that accept the tool’s plug.
Repair or replace damaged or worn cord
immediately.
2. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating less
than 150V:
This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated in
Sketch A in Figure 1. The tool has a grounding plug
that looks like the plug illustrated in Sketch A in
Figure 1. A temporary adapter, which looks like the
adapter illustrated in Sketches B and C, may be
used to connect this plug to a 2-pole receptacle
as shown in Sketch B if a properly grounded outlet
is not available. The temporary adapter should
be used only until a properly grounded outlet can
be installed by a qualified electrician. The green-
colored rigid ear, lug and the like, extending from
the adapter must be connected to a permanent
ground such as a properly grounded outlet box.
3. Grounded, cord-connected tools intended for
use on a supply circuit having a nominal rating
between 150-250V, inclusive:
This tool is intended for use on a circuit that
has an outlet that looks like the one illustrated
in Sketch D in Figure 1. The tool has a grounding
plug that looks like the plug illustrated in Sketch
D in Figure 1. Make sure the tool is connected to
an outlet having the same configuration as the
plug. No adapter is available or should be used
with this tool. If the tool must be reconnected
for use on a different type of electric circuit,
the reconnection should be made by qualified
service personnel; and after reconnection, the
tool should comply with all local codes and
ordinances.
4. Permanently connected tools:
This tool should be connected to a grounded
metal permanent wiring system; or to a system
having an equipment-grounding conductor.
B. FOR ALL DOUBLE-INSULATED TOOLS
1. Replacement parts
When servicing use only identical replacement
parts.
2. Polarized Plugs
To reduce the risk of electric shock, this
equipment has a polarized plug (one blade
is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in
any way.
Summary of Contents for ShopSeries RK7032
Page 1: ...RK7032 DRILLPRESS PaGE6 ENG TaLaDRODECOLuMNa PaGE14 ESP PERCEuSEÀCOLONNE PaGE23 FRE ...
Page 3: ...RK7032 1 2 3 4 5 6 7 10 11 12 13 14 15 16 9 8 ...
Page 4: ...C E G1 B D F G2 H2 A 8 a c d b b 10 9 9 b e 11 d H1 ...
Page 5: ...K M J L N I f O Q P E D C B A A B C D E 830 1200 1700 2300 3300 ...