Rockwell powerflex 700h Programming Manual Download Page 57

Page: 57 / 104

Chapter

Troubleshooting

This chapter provides information to guide you in troubleshooting the
PowerFlex 700H. Included is a listing and description of drive faults (with
possible solutions, when applicable) and alarms.

Drive Status

The condition or state of your drive is constantly monitored. Any changes
will be indicated through the LEDs and/or the HIM (if present).

Front Panel LED Indications

Figure 3.1 Drive Status Indicators

For information on…

See page…

Manually Clearing Faults

3-3

Fault & Alarm Descriptions

3-3

Clearing Alarms

3-10

Common Symptoms and Corrective Actions

3-10

Technical Support Options

3-12

Name

Color

State

Description

➊

PWR (Power)

Green

Steady

Illuminates when power is applied to the drive.

➋

PORT

(1)

Refer to the Communication Option User Manual for details.

Green

–

Status of DPI port internal communications (if present).

MOD

(1)

Yellow

–

Status of communications module (when installed).

NET A

(1)

Red

–

Status of network (if connected).

NET B

(1)

Red

–

Status of secondary network (if connected).

➋

➊

Summary of Contents for powerflex 700h









































































































Search results

Summary of Contents for powerflex 700h

Reviews:

Related manuals for powerflex 700h

Brands by name

Popular brands

Rockwell powerflex 700h, Programming Manual

Search results

Summary of Contents for powerflex 700h

Reviews:

Related manuals for powerflex 700h

Brands by name

Popular brands