Rockwell Automation Allen-BradleyPowerFlex 700AFE Installation Instructions Manual Download | Manualshive

Page: 69 / 296

background image

Rockwell Automation Publication PFLEX-IN029B-EN-P - August 2014

69

PowerFlex 700H and 700S Drives - Frame 10 Procedures

Chapter 2

Main DC Fan Power Supply System (SK-H1-DCFANBD1) Removal and
Installation

Note: PowerFlex 700H and 700S frame 10 drives have two fan power supplies.
You can retrofit an existing AC fan system or replace a DC fan system with a new
DC fan system. See Energy-related Products Fan Efficiency Directive on page

for guidelines on replacing an existing fan system with a new DC fan system.

Note: Retain the fan power supply sheet metal bracket for reuse.

Follow these steps to remove and replace an existing fan system with a new DC
fan system.

1.

Review the General Precautions on page

2.

Remove power from the drive. See Remove Power from the Drive on page

.

3.

Move the control frame and remove the air flow plate and protective
covers from the drive. See Move the Control Frame and Remove the Air
Flow Plate and Protective Covers on page

4.

Remove the appropriate main fan assembly. See Remove the Main AC or
DC Fan Power Supply Assemblies on page

.

«
...
67
68
69
70
71
...
»

Summary of Contents for Allen-BradleyPowerFlex 700AFE









































































































































































































































































































Reviews:

No comments

Related manuals for Allen-BradleyPowerFlex 700AFE

C1400-CO-VS-0S-I03

Brand: NTI AG Pages: 20

PARAMAX M Series

Brand: Sumitomo Drive Technologies Pages: 24

Brand: Tandon Pages: 105

ADAP-KOOL AKD 102

Brand: Danfoss Pages: 130

Brand: Yuhai Pages: 168

Brand: Commodore Pages: 48

Brand: Tridonic Pages: 14

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 16

Brand: Philips Pages: 39

Brand: Philips Pages: 40

Brand: Philips Pages: 48

Brand: Philips Pages: 76

Brand: Philips Pages: 122

Brand: Toshiba Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands