background image

Rockwell Automation Publication PFLEX-IN029B-EN-P - August 2014

67

PowerFlex 700H and 700S Drives - Frame 10 Procedures

Chapter 2

Main AC Fan Inverter Circuit Board (20-VB00299) and AC Fan Output 
Transformer Assembly [20-FR10844 (Left) or 20-FR10845 (Right)] 
Removal and Installation

PowerFlex 700H and 700S frame 10 drives have two fan inverters. You can 
replace a fan inverter circuit board, or replace an output transformer assembly 
(includes the output transformer and fan capacitor on the assembly). See 
Isolating a Faulty Fan Inverter on page 

265

 for test procedures used to determine 

if the circuit board requires replacement.

Follow these steps to remove and replace a fan inverter circuit board or output 
transformer assembly.

1.

Review the General Precautions on page 

17

.

2.

Remove power from the drive. See Remove Power from the Drive on page 

59

.

3.

Move the control frame and remove the air flow plate and protective 
covers from the drive. See Move the Control Frame and Remove the Air 
Flow Plate and Protective Covers on 
page 

60

.

4.

Remove the appropriate main fan inverter assembly. See Remove the Main 
AC or DC Fan Power Supply Assemblies 
on page 

63

.

5.

Disconnect the cables from connectors X4 and X5. 

X4 (Blue)

X5 (Black)

Series B capacitor in a left-side AC fan

inverter assembly shown.

Series A capacitor in a left-side AC fan 
inverter assembly shown

Right-side AC fan inverter assembly shown

Summary of Contents for Allen-BradleyPowerFlex 700AFE









































































































































































































































































































Reviews: