background image

7

 1.  Holding the material securely, release the Locking 

    Casters (27)

.

 2.  With one hand on the material and one hand on the cart, 

    carefully push the cart to its destination, paying close 

    attention to the terrain in front of the cart. 

Fig. 11.

Unloading Material

 1.  Make sure the cart is on a flat, level surface. The cart could 

    move or tip or the load could become unstable if unloaded on 

    uneven terrain.

 

>  Take special care and go slowly when moving 

  across uneven surfaces such as a door threshold; 

  material could shift or become unstable 

  during transport.

CAUTION

Lifting the Sheet Upright

 1.  Position yourself on the side of the sheet opposite the 

    Flip Stops (24 and 25).

 

 2.  Holding the sheet securely, reach underneath and release the 

    Latch Arm (26).

    

Flip Stops (24 and 25) must be rotated up 

and secured by tightening the 4-Star Knobs (10) before the 
sheet can be safely tilted upright. Load will fall when tilted 
unless Flip Stops (24 and 25) are engaged. Fig. 9.

    

Keep hands clear of the pivot point to avoid 

pinching fingers.

 3.  With sheet positioned against the Flip Stops (24 and 25) 

    slowly allow the sheet to tip upright, maintaining a secure 

    hold until the sheet stops moving and you’re sure the load 

    is stable on the cart. 

Fig. 10.

Transporting the Sheet

Fig. 11

Fig. 9

Fig. 8

Fig. 10

Bullet Pin

8

25

24

23

Summary of Contents for Material Mate









Reviews: