Robomower MS1000 Operating Manual Download Page 42

Page: 42 / 54

Robomow RS models

Chapter 6 Charging

Shock, injury, electrocution hazard!
Never use the Power Box or charge the Robomow in areas where extreme
dampness or wet contact is likely.
Never use a Power Box when the leads are damaged.
Use only the recommended Power Box for your Robomow.

Important:

It is recommended to place the Power Box in a sheltered, dry

location. The Power Box should be well ventilated and avoid exposure to
direct sunlight or rain.
Do

not

pack the Power Box inside a plastic bag: it will over-heat.

At the end of each mowing session, Robomow will automatically recharge at

the Base Station.

Charging time takes up to 2 hours, depending on conditions.

6.1 Charging During the Season

The Base Station is the primary charging source when Robomow is docking

and will maintain the optimal battery charge while awaiting departure.
.

6.2 Charging Out of Season

During out of season months, such as winter, it is required to keep Robomow

continuously charged to avoid damage to the batteries.

The mower should be stored and charged at temperature higher then -10

Connect Robomow directly to the Power Box as follows:

Remove Robomow from its Base Station.

Remove the Base Station Head (Charging Adaptor) by lifting the front

lever up and pushing the Adaptor forward from behind the Base Station.

(See Section 2.6.3).

Unplug the 20 m (65 ft.), Extension Cable and the Perimeter Wire from

the Base Station Head.

Place the cap at the end of the 20 m (65 ft.) Extension Cable and on the

exposed connector to protect it from rain and corrosion. Cover also the

Perimeter Wire connector.

Disconnect the DC Cable coming from the Power Box to the 20 m (65

ft.) Extension Cable. Lift the rubber seal behind the Base Station Head

(Charging Adaptor) upwards to reveal the connector. Connect the DC

Cable to the Base Station Head.

)

Note:

This is not the same place the 20 m (65 ft.) Extension Cable

was connected to the Base Station Head when it was on the Base

Station.

Slide the Base Station Head pins into the front slot of Robomow.

Robomow may

be re-charged

at Power Box

20 m (65 ft.)

Extension Cable

Summary of Contents for MS1000























































Search results

Summary of Contents for MS1000

Reviews:

Related manuals for MS1000

Brands by name

Popular brands

Robomower MS1000, Operating Manual

Search results

Summary of Contents for MS1000

Reviews:

Related manuals for MS1000

Brands by name

Popular brands