Roberts Gorden CoRayVac CRT-10, Installation, Operation & Service Manual

Page: 10 / 62

CORAYVAC ® I
NSTALLATION
O
PERATION AND
S
ERVICE
M
ANUAL
4 of 54
SECTION 2: INSTALLER RESPONSIBILITY
The installer is responsible for the follo w ing:
• To ens u re the system is designed in accordance
w ith the parameters of the CORAYVAC
®
design
man u al (P/ N 128500UK).
• To install the heater, as w ell as the gas and elec-
trical s u pplies, in accordance w ith applicable
specifications and codes. Roberts-Gordon rec-
ommends the installer contact a local b
u ilding
inspector or fire marshal for g u idance.
• To u se the information gi v en in a layo u t dra w ing
and in the man u al together w ith the local and
national codes to perform the installation.
• To install the heater in accordance w ith the
clearances to comb u stibles.
• To f u rnish all needed materials not f u rnished as
standard eq u ipment.
• To plan location of s u pports.
• To pro v ide access to b u rners for ser v icing on all
sides, for b u rner remo v al.
• To pro v ide the o w ner w ith a copy of this
installation, operation and ser v ice man u al.
• To ne v er u se heater as s u pport for ladder or
other access eq u ipment and ne v er hang or
s u spend anything from heater.
• To ens u re there is adeq u ate air circ u lation
aro u nd the heater and to s u pply air for comb u s-
tion and v entilation in accordance w ith local and
national codes.
• To safely and adeq u ately install heater u sing
materials w ith a minim u m w orking load of 33 kg
(75 lbs).
• To ens u re the heater is placed in a appro v ed
application.
2.1 Low Level User Instructions
In all sit u ations, clearances to comb u stibles m u st be
maintained. Signs sho u ld be posted in storage
areas to specify the maxim u m stacking height of
items placed belo w heater to maintain req u ired
clearances to comb u stibles. Minim u m clearances
m u st be maintained from v ehicles parked belo w the
heater. Ca u tion sho u ld be u sed w hen r u nning the
system near comb u stible materials s u ch as w ood,
paper, r u bber, etc. Consideration sho u ld be gi v en to
partitions, storage racks, hoists, b u ilding constr u c-
tion,etc.
A laminated w all tag is a v ailable for the CORAYVAC ®
heater as a permanent reminder of the safety
instr
u ctions and the importance of the req u ired
clearances to comb u stibles. Please contact Rob-
erts-Gordon or yo u r ROBERTS GORDO N ® indepen-
dent distrib u tor to obtain the w all tag. Affix the tag by
peeling off the backing of the adhesi v e strips on the
rear s u rface and position the tag on a w all near the
CORAYVAC ® heater (e.g. thermostat or Controller).
A copy of the w all tag (P/ N 91037912) is ill u strated
on the back co v er. This copy of the w all tag m u st be
affixed on the w all near the heater. Kno w yo u r model
n u mber and installed config u ration. Model n u mber
and installed config u ration are fo u nd on the b u rner
and in the Installation, Operation and Ser v ice Man-
u al. Write the largest clearance dimensions w ith per-
manent ink according to yo u r model n u mber and
config u ration in the open spaces on the tag. See
Page 6, Section 3.2 .
2.2 Corrosive Chemicals
Roberts-Gordon E u rope Limted cannot be responsi-
ble for ens u ring that all appropriate safety meas u res
are u ndertaken prior to installation; this is entirely
the responsibility of the installer. It is essential that
the contractor, the s
u b-contractor, or the o w ner iden-
tifies the presence of comb u stible materials, corro-
si v e chemicals or halogenated hydrocarbons*
any w here in the premises.
* Halogenated Hydrocarbons are a family of chemical
compounds characterized by the presence of halogen
elements (fluorine, chlorine, bromine, etc.). These com-
pounds are frequently used in refrigerants, cleaning
agents, solvents, etc. If these compounds enter the air
supply of the burner, the life span of the heater compo-
nents will be greatly reduced. An outside air supply must
be provided to the burners whenever the presence of
these compounds is suspected. Warranty will be invalid
if the heater is exposed to halogenated hydrocarbons.
2.3 National Standards and Applicable Codes
All Appliances m u st be installed in accordance w ith
the latest re v ision of the applicable standards and
local and national codes. This refers also to the elec-
tric, gas and
v enting installation. N ote: Additional
standards for installations in P u blic Garages, Aircraft
Hangars, etc. may be applicable.
CAUTION
Product Damage Hazard
Do not use heater in area containing
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.