manualshive.com logo in svg

Robe Color Wash 700E AT, User Manual

Share
Download
Robe Color Wash 700E AT User Manual Download Page 30

30

Parameter ID

Discovery command SET command

GET command

DISPLAY_LEVEL

*

*

PAN_INVERT

*

*

TILT_INVERT

*

*

DEVICE_RESET

*

DMX_PERSONALITY

*

*

DMX_PERSONALITY_DESCRIPTION

*

STATUS_MESSAGES

*

STATUS_ID_DESCRIPTION

*

LAMP_STATE

*

*

LAMP_ON_MODE 

 

1

*

*

DEVICE_HOURS

  

2

*

LAMP_HOURS 

 2

*

LAMP_STRIKES 

2

*

1

...Another options for this command (only for Robe´s fixtures):

 

 

 

value PARAMETER_DATA=0x84 - lamp OFF by DMX value on DMX channel

 

 

 

value PARAMETER_DATA=0x88 - lamp OFF if DMX is not present

2

...Commands relative resetable values

11. Error and information messages

Occured errors during fixture operation are signaled by warning icon on the display:

 

 

 

 

 

 

 

 

Press [ESC] to see the current error messages. Description of error messages:  

Active Lamp Timer  

This message appears if you try to switch on the lamp within 5 minutes after having switched it off (the lamp is 

too hot). The message will appear on the display if the lamp doesn’t ignite within 28 seconds. The ColorWash 

700E AT will store this information and automatically ignite the lamp when the 5 minutes period has expired.

Caution:

 The message is disabled if the lamp light sensor (function “Lamp Sensor”in menu Personality) is 

switched Off.

Lamp Error

The ignition of the lamp is seven times unsuccessful (the “

Active Lamp Timer

” message appeared six times 

before), and the display shows 

“

Lamp Error

”

, meaning that the lamp could be damaged or even missed or 

there could be a failure on the ignitor or ballast. 

Please place or replace the lamp and contact your dealer if the situation was not caused by the lamp.

Caution:

 The message is disabled if the lamp light sensor (function “Lamp Sensor” in menu Personality) is 

switched off.

Lamp Sensor Error

This message informs the lamp light sensor is failed. 

Caution:

 The message is disabled if the lamp sensor (function Lamp Sensor in menu Personality) is switched 

Off.

Overheated-Lamp Off

This message informs that the fixture head is had been overheated and the lamp was switched off by head  

temperature sensor.

Overheated-Lamp Low

This message informs that the fixture head is has been overheated and the lamp power is reduced.

Short Power Error

This message will appear if the fixture was shortly disconnect from the main.

Summary of Contents for Color Wash 700E AT






































Reviews:

No comments

Brands by name

Popular brands

Load more brands