Robe Color Spot 1200 AT, User Manual

Page: 34 / 43

34
Focus/Zoom/Frost --- This function resets focus,zoom and frost.
Iris/Effect --- This function resets iris and effect wheel.
8.9 Special functions
Use this menu for special services like adjusting lamp or adjusting effects.
Lamp Adjustment --- This function can be used when you make the fine adjustment of the lamp.If you select this
function,all effects will be canceled,shutter will be opened and the dimmer intensity will be set onto 100%.By
using the options "PAn, Tilt, Zoom,Focus" you can focus the light on a flat surface (wall) and perform the fine
lamp adjustment.
Effect Adjustment --- By this function you can calibrate and adjust the effects to their standard/right
positions.Disconect the DMX controller from the fixture and select "DMX Values" menu.The display shows step
by step effects by which you can adjust the fixture to the required position before the function calibration. When
the positioning is finished ,select "Calibrate Values" and press [ENTER]:
1. Calibration via the control board
Select desired effect, press [ENTER] and adjust its right value (0 - 255). This can be repeated for each calibred
effect if it is required. When the calibration is finished, it is necessary to use the "Save and Reset" function to
write the calibration values to the memory and to make a reset in order to check the newly adjusted positions of
the calibrated effects.
List of the calibrated effects:
Pan Yellow Gobo 2 Indexing
Tilt Conversion Filter Effect Wheel
Colour Wheel Gobo Wheel 1 Effect Indexing
Cyan Gobo 1 Indexing Iris
Magenta Gobo Wheel 2 Dimmer
2. Calibration via the DMX controller
Connect the DMX controller to the fixture.Select desired effect and press [ENTER].Now you can calibrate the
selected effect by your controller.
DMX calibration protocol for Mode 1 (24 control channels):
Pan................ channel 25 Yellow ................ channel 30 Gobo 2 Indexing..... channel 35
Tilt................. channel 26 Conversion Filter.. channel 31 Effect Wheel...........channel 36
Colour Wheel... channel 27 Gobo Wheel 1...... channel 32 Effect Indexing........channel 37
Cyan.............. channel 28 Gobo 1 Indexing...channel 33 Iris.........................channel 38
Magenta......... channel 29 Gobo Wheel 2...... channel 34 Dimmer...................channel 39
DMX calibration protocol for Mode 2 (32 control channels):
Pan................ channel 33 Yellow ................ channel 38 Gobo 2 Indexing..... channel 43
Tilt................. channel 34 Conversion Filter.. channel 39 Effect Wheel...........channel 44
Colour Wheel... channel 35 Gobo Wheel 1...... channel 40 Effect Indexing........channel 45
Cyan.............. channel 36 Gobo 1 Indexing...channel 41 Iris.........................channel 46
Magenta......... channel 37 Gobo Wheel 2...... channel 42 Dimmer...................channel 47
After having calibrated required effects ,use the "Save and Resset" function to write the calibration values to the
memory and to make a reset in order to check the newly adjusted positions of the calibrated effects.
9. Low power mode
This mode omits fixture reset after switching the fixture on and lowers motor powers of the fixture."Low power
mode" is useful in special casech.g. if the fixture is in a flight case and you want to set its DMX address without
taking it out from the case.To enter "Low power mode":
Press and hold [ENTER] and at the same time switch on the Power switch.The following message appears:
Realy Skip Initial Reset?
Escape/Enter
Press [ENTER] to activate "Low power mode" without fixture reset.Now you can set features and behaviour of the
fixture by using "Fixture Address"menu and "Personality" menu.It is expected,that this mode will be exited by
switching the fixture off ,but if you want to go directly to "normal operation mode",execute any fixture reset.
Note:All motors in "Low power mode" are deactivated and switching the lamp on from the control panel
is blocked.