manualshive.com logo in svg

RMS R325I, User Manual, Page: 26 / 26

Share
Download
RMS R325I User Manual Download Page 26

RMS Technologies 

Page 26 

Version 1.20 

R325I Single Axis Controller/Driver Manual 

 

02/13/2006 

 

 

Driver to Motor Cable AWG Table 

1 Amp (Peak) 

 

5 Amp (Peak) 

Length 

(Feet) 10 25 50 75  100  Length 

(Feet) 10 25 50 75  100 

Minimum 

AWG 20 20 18 18  16   Minimum 

AWG 16 16 14 12  12 

 

 

 

2 Amp (Peak) 

 

6 Amp (Peak) 

Length 

(Feet) 10 25 50 75  100  Length 

(Feet) 10 25 50 75  100 

Minimum 

AWG 20 18 16 14  14   Minimum 

AWG 14 14 14 12  12 

 

 

 

3 Amp (Peak) 

 

7 Amp (Peak) 

Length 

(Feet) 10 25 50 75  100  Length 

(Feet) 10 25 50 75  100 

Minimum 

AWG 18 16 14 12  12   Minimum 

AWG 12 12 12 12  12 

 

 

 

4 Amp (Peak) 

 

 

Length 

(Feet) 10 25 50 75  100  

Minimum 

AWG 18 16 14 12  12   

 

 

Driver to Motor Supply Cable Wire Size 

 

NOTE: 

These recommendations will provide optimal protection against EMI and RFI. The 

actual cable type, wire gauge, shield type and filtering devices used are dependent on the 

customer’s application and system.

 

 

NOTE: 

Always use Shielded/Twisted Pairs for the Driver DC Supply Cable, the AC Supply 

Cable and the Driver to Motor Cable.

 

 

 
 

Summary of Contents for R325I



























Reviews:

No comments