background image

 

4 • 61-1004RK/61-0191RK Combustible Gas Detector

Overview

This manual describes the 65-1004RK CO

2

 (carbon dioxide) detector. This manual also 

describes how to install, start up, maintain, and calibrate the detector when used with a 
gas monitoring controller. A parts list at the end of this manual lists replacement parts and 
accessories for the CO

2

 detector.

The 61-1004RK CO

2

 detector includes a junction box. This manual may also be used for 

the 61-0191RK CO

2

 detector which does not include a junction box and is normally 

mounted in one of a controller’s conduit hubs and factory wired to the controller. If you 
are using a 61-0191RK CO

2

 detector, disregard all references to the junction box and 

junction box terminal block.

Specifications

Table 1 lists specifications for the CO

2

 detector.

Table 1: 61-1004RK Specifications

Detection Range

With Junction Box
61-1004RK-02: 0 - 5,000 ppm CO

2

61-1004RK--03: 0 - 5% volume CO

2

Without Junction Box
61-0191RK-02: 0 - 5,000 ppm CO

2

61-0191RK-03: 0 - 5% volume CO

2

Area Classification

Explosionproof for Class I, Groups B, C, and D

Sampling Method

Diffusion

Response Time

90% in 45 seconds 

Summary of Contents for 61-0191RK














Reviews: