RJM MasterMind, User Manual, Page: 21 / 29

15
IA4
- Instant Access 4 Mode
(Instant Access Mode range:
LAT
,
PULS
,
Grp
, Default value:
LAt
)
This controls the behavior of Instant Access button 4.
LAT
(latching) is the default behavior: each press of the IA button
toggles it between on and off.
PuLs
(momentary pulse) means that the switch stays on while you’re holding the button
down, but turns off as soon as you release the button (this is particularly useful for tap tempo control).
Grp
(group)
means that pressing this switch will turn off all other IA switches that are set to
Grp
– the MasterMind will insure that
no more than one switch in the group can be on at a time.
IA5
- Instant Access 5 Mode
(Instant Access Mode range:
LAT
,
PULS
,
Grp
, Default value:
LAt
)
This controls the behavior of Instant Access button 5.
LAT
(latching) is the default behavior: each press of the IA button
toggles it between on and off.
PuLs
(momentary pulse) means that the switch stays on while you’re holding the button
down, but turns off as soon as you release the button (this is particularly useful for tap tempo control).
Grp
(group)
means that pressing this switch will turn off all other IA switches that are set to
Grp
– the MasterMind will insure that
no more than one switch in the group can be on at a time.
SNDA
- Send Always
(Send Always range:
On
,
OFF
, Default value:
On
)
When this parameter is on, pressing a preset button (1 through 5) will always cause the MasterMind to send the
corresponding PC and CC messages, even if the MasterMind is already on the selected preset. If this parameter is off,
the MasterMind will only send PC and CC messages when selecting a new preset – pressing the same preset button
repeatedly will not generate multiple sets of PC and CC messages.
PCAL
- Pedal Calibration
(Yes/No selection: Press Bank Up (Yes) to start pedal calibration, Bank Down (No) to exit Setup Mode)
Pressing Bank Up when this parameter is selected will cause the MasterMind to begin expression pedal calibration.
Calibration insures that the MasterMind knows the upper and lower limits of pedal travel, which are needed to provide
the best pedal performance. When in pedal calibration, the display will read
CAL
. With the expression pedal plugged in
to the MasterMind, move the pedal to the fully up position, then to the fully down position. On the MasterMind display,
an indicator on the right side of the screen should move to the top when the pedal is fully depressed, and should move
to the bottom when the pedal is raised up.
Once you’ve moved the pedal through its full range of motion, press any button on the MasterMind to exit calibration.
SEND
- MIDI Dump Send
(Yes/No selection: Press Bank Up (Yes) to send, Bank Down (No) to exit Setup Mode)
Pressing Bank Up when this parameter is selected will cause the MasterMind to send its configuration data out the MIDI
Out port. If the MIDI Out port is connected to the MIDI In port of another MasterMind, the data will be transferred to the
MasterMind. The data can also be sent to a PC that has a MIDI interface and SysEx librarian software for backup
purposes.
InIt
- Initialize
(Yes/No selection: Press Bank Up (Yes) to initialize, Bank Down (No) to exit Setup Mode)
Pressing Bank Up when this parameter is selected will cause the MasterMind to erase its memory, returning to the
factory default state. Be careful! This wipes the entire memory and there’s no way to restore your settings unless you
have previously backed them up to a PC or another MasterMind.
Preset Setup
Once you’ve finished Global Setup , you can set up each preset. In this mode, you set which Program Change number is
sent to each Program Change destination, and set which controller value is sent for each Continuous Controller for
every preset. You can also set up the Function button and Expression Pedal for each preset in this mode.
Entering Preset Setup
The MasterMind goes straight to Preset Setup when you enter
Setup Mode . If you happen to be in Global Setup , you
can press the 1 / Function Select button to switch to Preset Setup. The red LED above the 1 / Function Select button
will light to tell you that Preset Setup is active. You are now ready to edit the first parameter.