background image

Rivers Edge® Treestands, Inc.
1160 Eighth Avenue, PO Box 755
Cumberland, WI 54829
800-450-EDGE (3343) |  Fax 715-822-2124
Email: [email protected]

*All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images 

may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.

Operator's Manual

GRIP RAIL™ Climbing Aids

INSPECTION AND MAINTENANCE SCHEDULE

BEFORE EACH USE PERFORM THE FOLLOWING:

•  Inspect all webbing, rope, cord, and strap assemblies for wear or 

damage.

•  Inspect cables and/or cable ends for damage or kinking.
•  Inspect all hardware and chain components for damage.
•  Inspect for any structural damage to product. (If any exists call RETI 

customer service.)

•  Inspect all nut and bolt assemblies to be certain none are loose.
•  Inspect for any missing parts.
•  Lubricate all pivot and slide together points with powder graphite, 

petroleum jelly or silicone spray to prevent noise, wear and rust.

•  Inspect entire product for any rust, corrosion, cracks, freezing, 

excessive heat or rotting damage that may effect the safety of your 

product. Discard any questionable product.

•  Inspect entire product for any structural damage - pay close 

attention to all weld locations. (Return to factory for repair or 

discard product if any damage is found.)

•  Using correct wrenches inspect all nut & bolt assembly locations 

and snug up any that may be loose. Be careful not to crush tubing 

when tightening!

•  Inspect and check operation of all cables, cable ends, cord, rope, 

webbing, and strap or chain assemblies. Replace with factory new 

any item or assembly that shows signs of wear, damage, kinking, or 

functions incorrectly.

•  Inspect seat. Replace any seat with factory new that shows signs of 

structural damage or wear.

•  Inspect all hardware for wear or damage, also be sure you have no 

missing parts.

•  Never modify your stand in any way by making repairs, replacing 

parts, or altering adding or attaching anything to it except if 

explicitly authorized in writing by the manufacturer.

WARNING

Sectional ladders and steps shall be spaced on the tree to 

insure each step is no more than 18 in. (45.72 cm) apart.
Check every stick ladder section connection every time 

you use the stick ladder before you leave the ground. If 

stick ladder sections are separating, 

Do Not

 use the stick 

ladder.
Read and perform all inspection and maintenance tasks 

before each and every use. Replace any questionable 

components immediately with RETI original replacement 

parts.

Always

 maintain three (3) points of contact when 

Ascending or descending a ladder or climbing aid. Proper 

three-point contact means having either two feet with 

one hand or one foot with two hands on the step portion 

of the ladder or climbing aid at all times.

Always

 wear the appropriate footwear when using a 

treestand or climbing aid. A good non-slip safety boot is 

important to your personal safety. Be especially careful 

that boot laces do not get hooked on the stand, climbing 

aid or any of their components (tuck shoelaces into boots 

before climbing).

Always

 lean forward as you ascend or descend ladder or 

climbing aid. 

Never

 Lean out over edge of device.

Double check assembly steps to be certain you have 

correctly assembled this product.
Replace any and all treestand or climbing aid straps every 

two years or when any signs of damage or wear exist 

before.

Never

 hold onto any section or pull on any section that is 

not securely attached to the tree with the provided strap 

and buckle.

Always

 attach the cam strap assembly so the spring 

loaded cam lever of the strap is facing away from the tree. 

Never

 touch the cam lever while putting weight on the 

stick and/or climbing the stick as this could potentially 

release the strap and remove that section from the tree.

Do Not

 crush tubing when tightening bolt assemblies! 

Identify and familiarize yourself with all parts before you 

start.

Never

 use any product that has not been maintained or 

inspected properly - Your life depends on it!
Use a haul line to raise and lower the treestand. 

Never

 

climb with anything on your back.

Do not remove labels/warnings from product, they are 

there for your safety.
Recommended for adult use only. 

Reviews: