Elmdene Quartz-1000-G3 Manual Download

Page: 1 / 10

Technical Support Line +44 (0)23 9269 6638 (Option 3)

PAK200544 Iss 01A Mar 2012

QUARTZ-G3 Range
External Sounder

Models

QUARTZ-1000-G3, QUARTZ-3000-G3

EATURES

108dB(A) siren output

12v dc voltage operation

Integral low current LED strobe.

2 way tamper protection: cover & rear

Separate sound and strobe trigger inputs

Hold-off supply failure detection

Battery and piezo test with fault output

Selectable sound auto cut-off timer: 5s (for test)

or 15 minutes

Full SAB using internal battery

Twin Comfort LEDs selectable on, off, alternate

flash

Audible Tamper to assist commissioning

Ring Line Monitoring

Engineer Mode for quiet installation and

maintenance

Polycarbonate cover and backplate

Microprocessor controlled

Elmdene International Ltd

Tel: +44(0)23 9269 6638

3 Keel Close, Interchange Park,

Fax: +44(0)23 9266 0483

Portsmouth, Hampshire, PO3 5QD, UK

Web:

www.elmdene.co.uk

Summary of Contents for Quartz-1000-G3











Search results

Summary of Contents for Quartz-1000-G3

Reviews:

Related manuals for Quartz-1000-G3

Brands by name

Popular brands

Elmdene Quartz-1000-G3, Manual

Search results

Summary of Contents for Quartz-1000-G3

Reviews:

Related manuals for Quartz-1000-G3

Brands by name

Popular brands