background image

1 About this documentation 

 

Ritta l S22 insulation stripping machine  

We reserve the right to make technical m odifications. 

EN 

1

 

About  this documentation 

The warnings in this documentation are structured differently depending on the 
severity of danger. 

 

 

Warning! 
Possible risk of fatality! 
Notices with the signal word "warning" warn you about situations 
which could lead to fatal or serious injuries if you do not pay attention 
to the notices specified. 

 

 

 

Caution! 
Risk of injury! 
Notices with the signal word "caution" warn you about situations 
which could lead to injury if you do not pay attention to the notices 
specified. 

 

 

Attention! 
Property damage! 
Notices with the signal word "attention" warn you about dangers which could 
result in damage to property. 

 
Situation-related warnings may contain the following warning symbols: 

 

Symbol 

Meaning 

 

Warning: dangerous electrical voltage 

 

Warning: injury to hands due to sharp blades 

 

Work may only be performed by a qualified electrician 

 

Only perform work with personal protective equipment  

 

Disconnect the mains plug 

 

Notes on documentation 

 
Additional formatting is used in the rest of the text which has the following mean-
ing: 

 

 

Note: 
This constitutes information which is not related to safety, but which 
provides important information regarding correct and effective work. 

 

 

This symbol indicates an "action point" and shows that you should perform an 
operation or procedure. 

Summary of Contents for AS 4050.451






















Reviews: