background image

4 Assembly and siting

EN

14

Rittal Micro Data Center Level E

Rittal Micro Data Center Level E, 47 U, 1200 mm interior depth with two single-leaf doors

Components

Weight [kg]

Average surface load assuming a total weight of 

1340 kg (based on one Micro Data Center)

Mico Data Center Level E

800

Line a.) 

437 kg/m²

 on a bare floor

TS-IT rack

90

Climate control unit

(LCP is not considered)

150

Live load

300

Line b.) 

868 kg/m²

 directly below the Micro Data Center sur-

face for floating floors or surface coverings, etc.

Total weight

1340

Rittal Micro Data Center Level E, 47 U, 1200 mm interior depth with two double-leaf doors

Components

Weight [kg]

Average surface load assuming a total weight of 

1340 kg (based on one Micro Data Center)

Micro Data Center Level E

800

Line a.) 

566 kg/m²

 on a bare floor

TS-IT rack

90

Climate control unit

(LCP is not considered)

150

Live load

300

Line b.) 

868 kg/m²

 directly below the Micro Data Center sur-

face for floating floors or surface coverings, etc.

Total weight

1340

Danger of collapse
The failure of the building structure can 
cause severe injuries and death.
Prior to the assembly of the Micro Data 
Center, check the requirements placed 
on the building statics.
The Micro Data Center may be posi-
tioned only where the building structure 
is dimensioned adequately.

Summary of Contents for 7999.009









































Reviews: