Ritron AIERIT27-150, Owner'S Manual

Page: 26 / 61

Section 4
Operation 22
4.
t first send the correct 2-Tone Paging code. Once access to the
lo hile on the
Lo en require the
co c
4. fore transmitting to be sure there are no other radio users on the Loudmouth
nd, allowing the pre-announce tone to be heard.
h
10. If the radio PTT is pressed again before the Loudmouth receiver has reset, the message will be heard on
aging code.
11.
th
3
2-Tone Paging
To access the Loudmouth
™
the 2-way radio mus
udspeaker is accomplished, the user simply presses the 2-way radio’s PTT and speaks w
™ ™
udmouth channel. After a period of inactivity the Loudmouth will automatically reset, and will th
rre t 2-Tone Paging code to re-gain access.
1. Move to an area that is away from the Loudmouth
™
speaker to prevent feedback.
2. Be sure the microphone on the calling radio is pointed away from the Loudmouth
™
speaker.
3. Set the portable, base station, or mobile radio to the Loudmouth
™
channel.
Monitor the channel be
™
frequency.
5. Send the correct 2-Tone Paging code. Refer to your 2-way radio’s user manual to determine how you send
2-tone paging codes.
6. Wait until the entire 2-tone code has been sent.
7. Press and hold the PTT button and pause for about 1 seco
8. Speak into the radio microphone to broadcast your message over the Loudmouth
™
speaker. If other radios
are operating on the Loudmouth
™
channel they will also ear your message.
9. Release the PTT button when your message is complete.
™
the speaker without the need for a 2-tone P
Return the portable, base station, or mobile radio to the normal operating channel.
Wi 2-Tone Paging operation:
Once Loudmouth receiver has decoded the correct 2-tone code any radio on the Loudmouth
channel can talk over the speaker without the need for 2-tone paging.
•
g a signal before 2-tone is once again
required for access. Factory default Two-Tone Reset Time is 5 seconds.
• Can be used in conjunction with QC or DQC for added security. The 2-way radio and the Loudmouth
™
grammed for the same QC or DQC code
.
4.
W der
th
messa them back over the speaker when the PTT button is released on the 2-way radio. Set the
portab annel.
os are
n the Loudmouth
™
channel they will hear your message as you record it.
5. d and the Loudmouth
™
speaker will begin playing your recorded
6. he he normal operating channel.
™ ™
• After a 2-tone code has been successfully decoded, the programmable Two-Tone Reset Time sets the
length of time the Loudmouth
™
receiver can go without receivin
receiver must be pro
4
Record and Play
(20 seconds of record time MAXIMUM)
™
hen 2-way radios are used in the same area as the Loudmouth speaker, feedback may result that can ren
e system unusable. For those applications the Loudmouth
™
can be programmed to record the incoming
ges and play
le, base station, or mobile radio to the Loudmouth
™
ch
1. Monitor the channel before transmitting to be sure there are no other radio users on the Loudmouth
™
frequency.
2. Press and hold the PTT button on your 2-way radio.
3. Speak into the radio microphone to record your message into the Loudmouth
™
receiver. If other radi
operating o
4. Release the PTT button when your message is complete.
The pre-announce tone will be hear
message.
W n finished, return the portable, base station, or mobile radio to t
With Record and Play operation:
Recorded messages are limi • ted to a maximum of 20 seconds.
naling options can be used in conjunction with Record and Play.
• The Loudmouth
™
receiver cannot record (buffer) an incoming message while in the process of playing
• Any of the selective sig
a message on the speaker.