background image

Page 7

DLS350 User Guide

Light Source Accessories

Light Source Adapters

Part Number

Description

AC 022B

SC Adapter

AC 023B

FC Adapter

AC 024B

ST Adapter

AC 025B

LC Adapter

Patch Cord Accessories

Part Number

Description

AC 550

MM SC-LC - 1m simplex

AC 551

MM SC-SC - 1m simplex

AC 552

MM LC-LC - 1m simplex

AC 600

SC-SC simplex bulkhead

AC 601

LC-LC simplex bulkhead

Certifications, and Contact Information

The DLS350 comes calibrated and should be recalibrated every 2 years. Included with the DLS350 is a calibration 

certificate, and free recalibration within 2 years of the date of purchase. To start the calibration process simply call or email 

technical support!

Calibration Certificates

The DLS350 comes with a 2 year warranty for any manufacturer defects or damage due to reasonable use. To start the 

RMA process simply email or call technical support!

Warranty

LED SOURCE

Wavelength

850nm & 1300nm

Output Power

-22.00 dBm

Output Stability

±0.05dB (1 Hour)

±0.03dB Long-Term (15 min warm-up)

Spectral Width

40nm / 120nm

Optical Interface

SC/FC/ST/LC Interchangeable

Tone Output

2 kHz

LED Class

Class 1 (IEC 62471:2006)

Power

Push Button Toggle

Battery

CR2

Operating Temperature

-10° to +50° C

Storage Temperature

-30° to +60° C

Dimensions

15.5cm x 2.38cm x 1.9cm

Weight

3 oz

Specification

Summary of Contents for Miller DLS350









Reviews: