RioOutdoors 6P-SH Installation Instructions Manual Download | Manualshive

Page: 17 / 24

background image

17 |

P a g e

1.9

HEADERS INSTALLATION

1.

Lift and place one header with rafter ties in the U-channels on two adjacent post-top brackets.

2.

Center the header between the two posts by measuring the overhangs and moving the header until the overhang

lengths on both sides are equal.

3.

Locate the two 5/16” holes, one on each wing extension of the post-top single header bracket. Drill 3/32” X 1-1/4” deep

pilot holes at the center of the two 5/16” Holes. Locate pilot holes at the center of each 5/16” hole.

«
...
15
16
17
18
19
...
»

Summary of Contents for 6P-SH

























Reviews:

No comments

Related manuals for 6P-SH

Brand: Nayer Pages: 7

Brand: TENTCO Pages: 2

Brand: skandika outdoor Pages: 2

Weekender West Coast Frame

Brand: Party Tents Direct Pages: 16

Command Post 8334

Brand: Clam Pages: 5

Brand: Clarke Pages: 16

Brand: Clarke Pages: 20

Brand: Creative Structures Pages: 20

Brand: Coleman Pages: 4

Brand: Axley Pages: 10

Brand: Palram Pages: 27

Brand: Vango Pages: 3

Brand: Dancover Pages: 9

Brand: Quest Engineering Pages: 2

Brand: Jack Wolfskin Pages: 9

Brand: Euromate Pages: 6

TREK TENTS 283A

Brand: MMI OUTDOOR Pages: 2

Brand: MMI OUTDOOR Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands