Rinnai HD210E Operation & Installation Manual Download Page 4

Rinnai 

Commercial Manifold Pack OIM

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and to ensure 

optimum performance.
Failure to carefully read and follow all instructions in this manual can result in equipment 

malfunction, property damage, personal injury and/or death.

DANGER:

  Indicates an imminently hazardous situation which, if not avoided, will result in 

personal injury or death.

WARNINGS:

  Indicates a potentially hazardous situation which, if not avoided, could result in 

personal injury or death.

CAUTIONS:

  Indicates a potentially hazardous situation which, if not avoided, could result 

in minor or moderate injury or damage to the appliance. It may also be used to alert against 

unsafe practices.

WARNING

REGULATORY INFORMATION

This appliance shall be installed in accordance with these instructions and all regulatory 

requirements which exist in your area including those in relation to manual lifting, working at 

heights and on roofs. Applicable publications and regulations may include:

• 

AS/NZS 3500 National Plumbing and Drainage, AS/NZS 3000 Wiring rules, AS/NZ 5601 Gas 

Installations & Building Codes of Australia (BCA)

• 

Local Occupational Health and Safety (OH&S) regulations

• 

Local Regulations and Municipal Building Codes

DO NOT

 operate this system before reading the manufacturers instructions. 

This appliance must be installed, commissioned and serviced by an authorised person in 

accordance with all applicable local rules and regulations.
For continued safety of this appliance it must be installed, operated and maintained in accordance 

with the manufacturer’s instructions.
This appliance is heavy, use 2 people or mechanical lifting device. Improper lifting may result in 

serious injury.

DO NOT

 modify the electrical wiring of this appliance. If the control power wiring is damaged or 

deteriorated then it must be replaced only by an authorised person. Failure to do so may result 

in electric shock, fire, serious injury or product failure.

Care should be taken not to touch the pipe work as it may be HOT!

DO NOT

 place articles on or against this appliance.

DO NOT

 store chemicals or flammable materials near this appliance.

DO NOT

 operate with panels, covers or guards removed from this appliance.

DO NOT

 remove covers while power is on.

DO NOT

 enclose this appliance.

DO NOT

 activate pump unless cylinder is full of water.

Not suitable as a pool or spa heater.

All Rinnai Manifold Pack (MP) systems and components are Watermark Certified by SAI Global 

as applicable.

All dimensions referred to in these instructions are in millimetres, unless otherwise specified.

NOTE

A NOTE ON ILLUSTRATIONS

The illustrations used in this manual are for explanatory purposes only and the shape of your unit 

may vary slightly from that which is shown in this manual. 

NOTE

WARNINGS & IMPORTANT INFORMATION

Summary of Contents for HD210E

























Reviews: