manualshive.com logo in svg

Rinnai AH083CP, Installation And Operation Manual, Page: 9 / 48

Share
Download
Rinnai AH083CP Installation And Operation Manual Download Page 9

 

Hydronic Air Handler Installation and Operation Manual 

  

9

 

• 

Upflow

 

The blower should be set on top of the coil 
section being used and the blower must be 
supported on the bottom only and set on 
solid floor or a field

-

supplied supporting 

frame.

 

• 

Side Return (Left or Right Side)

 

Cut and remove panel as indicated by 
perforations. Attach evaporator coil with 
sheet metal screws (if using). Ensure bottom 
portion of unit is sealed properly to prevent 
air leakage. 

 

• 

Bottom Return

 

The air handler must be supported on the 
underside only and set on a field

-

supplied 

supporting frame. Remove the bottom plate 
of the air handler to create an air return 
opening. Securely attach the air handler to 
the supporting frame.

 

The air handler is approved for the following 
configurations: 

 

• 

Vertical: Upflow with bottom or side (left or 

right side) return

 

• 

Horizontal: Upflow with bottom return

 

SUPPLY (Upflow)

 

RETURN

 

The air handler is not approved for the 
following configurations:  

 

• 

The air inlet is not allowed in the front 
or back of the air handler.

 

Front

 

Back

 

• 

Multiple air handlers configured for 
installation with a single Rinnai 
tankless water heater or boiler is 
prohibited. 

 

• 

Do not position the air handler on its 
front panel.

 

Front 

 

Air flows in through bottom or 

side (left or right side)

 

Vertical (upflow with bottom or side return) 

 

Air flows out through top

 

Horizontal (Upflow with bottom return)

 

RETURN

 

Air flows in 

through 

“

bottom 

duct return

”

 

SUPPLY

 

Air flows 

out 

through 

“

top

”

 

Summary of Contents for AH083CP

















































Reviews:

No comments