manualshive.com logo in svg

Rinnai AH083CP, Installation And Operation Manual, Page: 7 / 48

Share
Download
Rinnai AH083CP Installation And Operation Manual Download Page 7

Hydronic Air Handler Installation and Operation Manual 

  

7

 

120V Power Supply 

Knockout Access Port 

1

 

24V Thermostat Cable 

Knockout Access Port 

(available on left or right 

side)

 

Left or Right Side HVAC 
Duct Return

 

Corrosion Resistant Cabinet 
(made of heavy gauge 
galvanized steel)

 

3

-

Speed PSC Blower 

Motor and Housing

 

Control Panel 

 

Water Inlet 

 

Hot Water From Water Heater/

Boiler into Air Handler

 

Hydronic 

 

Coil

 

Circulation Pump (for models 
with integrated pump). 
Circulates hot water between 
the air handler and tankless 
water heater/boiler. 

 

Water Outlet 

 

Cold Water Returning to 

 

Water Heater/Boiler

 

Bottom HVAC 

 

Duct Return

 

• 

Reference to the "top" and "bottom" 
are referring to the location in this 
image and will not change based on 
orientation of the product.

 

• 

Cover is removed in above image to 
show the air handler internal 
components. 

 

               

NOTE

 

TOP

 

BOTTOM

 

1

 

120V Power Supply Knockout Access Port: 

 

• 

Located on right side panel for air handler 
models AH083P/CP, AH084P/CP, AH125P/

CP, and AH166P/CP.

 

• 

Located on left side panel for air handler 
models AH206P/CP. 

 

 

A

-

Coil and Ductwork 

 

(Field

-

Supplied)

 

Control Panel

 

Air Handler

 

 

 

Water Outlet to 

 

Water Heater/Boiler

 

Water Inlet From 

 

Water Heater/Boiler

 

Refrigerant Lines (Field

-

Supplied) to Condensing Unit 

 

Summary of Contents for AH083CP

















































Reviews:

No comments