17
2002760_A_FR
Pour plus de renseignements, consultez
2. Une fois le chariot d’impression immobile, soulevez le
loquet de cartouche
d’encre
pour le placer en position ouverte.
3. Si une cartouche d’encre est déjà installée, faites glisser la
cartouche
d’encre
hors du logement pour cartouche d’encre.
4. Déballez une
cartouche d’encre
neuve.
5. Retirez délicatement la
bande de protection
qui recouvre les buses d’encre.
Important !
Ne touchez pas aux buses ou aux contacts en cuivre sur les
cartouches d’encre. Si vous les touchez, vous risquez de provoquer des
obstructions, des défaillances au niveau des cartouches d’encre et les
branchements électriques risquent d’en souffrir. Ne retirez pas les bandes
en cuivre.
6. Tenez la
cartouche d’encre
de sorte que la bande en cuivre soit en bas et
orientée vers l’imprimante.
7. Faites glisser la
cartouche d’encre
dans le logement.
8. Appuyez sur le
loquet de cartouche d’encre
jusqu’à ce qu’il s’enclenche.
9. Fermez la
porte d’accès aux cartouches d’encre
. Le témoin d’état des
cartouches d’encre clignote pendant quelques secondes. Lorsqu’il cesse de
clignoter, l’imprimante Rimage 2000i est prête à imprimer.
Remarque :
Si la cartouche d’encre ne repose pas correctement dans son
logement, l’imprimante ne la reconnaîtra pas. L’imprimante peut ne pas se
réinitialiser correctement ou un message de cartouche d’encre incorrecte
peut s’afficher. Si ceci se produit :
•
Retirez la cartouche d’encre et réinsérez-la. Appuyez fermement sur la
cartouche lorsque vous la réinsérez.
•
Veillez à utiliser la cartouche appropriée. Les cartouches acceptées sont
affichées dans la section
•
Si le problème persiste, remplacez la
cartouche d’encre
.
10. Alignez les cartouches d’encre. Reportez-vous à la section
Tests de diagnostic
Cette section fournit des informations nécessaires pour afficher, sélectionner
et effectuer des tests de diagnostic sur l’appareil Rimage 2000i. Avant de
commencer, vérifiez que l’imprimante Rimage 2000i ne présente pas d’erreur.
Important !
N’exécutez que les tests de diagnostic mentionnés ci-après.
N’essayez pas d’exécuter d’autres tests de diagnostic sans l’aide d’un technicien
Rimage expérimenté
Accès au mode de diagnostic
1. Mettez l’imprimante
Rimage 2000i
sous tension.
2. Attendez que l’initialisation du système soit complète.
Remarque :
L’initialisation du système Rimage 2000i peut durer jusqu’à
5 minutes.
3. Appuyez sur le
bouton de commande
et maintenez-le enfoncé jusqu’à ce
que l’intitulé [BUTTON DIAGNOSTIC] (Bouton de diagnostic) s’affiche sur le
panneau de l’opérateur.
Remarque :
D’autres messages d’état s’affichent sur le panneau de
l’opérateur lorsque vous appuyez sur le bouton de commande. Ne relâchez
pas le bouton avant que le message [BUTTON DIAGNOSTIC] ne s’affiche sur
le panneau.
4. Relâchez le
bouton de commande
. L’appareil Rimage 2000i est en mode de
test de diagnostic.
Maintenance du Rimage 2000i Series II
Summary of Contents for 2000i Series II
