RIHO Anna BZ79005, Installation And Operation Manual

Page: 4 / 124

EN
EN
EN
Whirlpool T LCD - Manual
IW00290.1
THE MANUFACTURER REFUSES TO ACCEPT ANY LIABILITY IN THE FOLLOWING CASES:
=
Legal requirements or provisions for earthing, protective and electrical installation in the bathroom have not
been met
=
The applicable laws and standards for bathrooms have not been complied with
=
The instructions in this manual have not been followed.
Parts are dismantled after inspection in the factory to facilitate transport and to enable it to be carried into the room in which
it is to be installed. It is advisable to check all the components of the bath before installation.
Any damage claimed after installation will not be covered under the guarantee.
Fig. 1 Safety distances.
1.0 Installation of R IHO Whirlpools
1.1 Safety regulations for bathrooms.
Electrical sockets, lamps, switches and/or other electrical equipment should be
installed outside the danger zones indicated in the national guidelines and standards.
Above all, the regulations prohibit the presence of any electrical installation within 60
cm around the bath, and less than 225 cm above it (see Fig.1). The switch and other
electrical devices should be installed so as to be inaccessible to the person using the
whirlpool.
The Whirlpool baths are fully in conformity with the applicable EN and national guidelines.
N OTICE:
=
The installation of the bathtub must be carried out by an appropriately certified worker .
=
The installation of the bathtub must be carried out in accordance with the assembly instructions given in these
instructions and drawings for the bath, where its dimensions are stated; The position of the supports and
fasteners is unique for each bathtub and must be found on the bathtub supplied
.
=
The customer is responsible for the proper preparation of construction, wiring and plumbing work .
=
Use of cleaning materials other than those recommended by the manufacturer may result in damage to the tub
and / or whirlpool system .
=
Testing and restoring current protectors must be performed regularly .
=
This appliance may be used by children under 8 years of age and older and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if supervised or instructed to use the
appliance in a safe manner and understand the potential hazards
.
=
Children can not play with the appliance .
=
Cleaning and maintenance carried out by the user must not be carried out by children without supervision .
=
The maximum allowable altitude for the use of the device is 2000 m. M.
=
If the power supply is damaged and if there is any malfunction (eg nozzle, engine, light humidity, etc.) the
bathtub must be turned off and contact the RIHO service department .
=
Parts containing live parts, except for parts powered by a safe low voltage not exceeding 12 V, shall not be
available to the person in the bath .
=
Parts containing electrical components other than remote control devices must be located or fixed in such a
way that they can not fall into the bath .
The whirlpool bathtub must only be adjusted by installers who can demonstrate to the competent authorities
knowledge and skills to meet national safety requirements, ie water intake / drainage and power supply.
B efore first use, the following test shall be carried out:
A fter installation, check if the bathtub is clean. The bath is filled with water at an inlet temperature of 40 +/- 5 ° C to
the level above the highest nozzle that allows the system to operate. Turn on the system and let it run for at least 10
minutes. Test the aero motor by using all 5 levels at least once during the test. Without draining, the whirlpool system shuts
off 30 minutes after the last button has been touched. Check all pipelines, connections for leakage of water.
A fter all necessary adjustments to ensure the integrity or replacement of any defective elements, the procedure is
repeated.
T he installer and the first whirlpool owner must provide instructions for use and maintenance to other owners and users.
1.4 Pre-installation actions
Before connecting the bathtub, it must be installed :
- Ventilation grid for the motor(s) of at least 100cm² for each Hydro or Aero system and 2 00cm² for combined
systems Hydro/Aero.
- It is recommended to install 2nd ventilation grid for natural ventilation (to the extent possible, they should be
placed as far apart as possible). Both grids together have then at least 2 00cm² .
- Inspection hatch(es) of at least 40 x 50cm for service access (at least to the motors). In front of the openings, a
space of at least 50 cm width must be freely accessible for access to the technique - see Figure 5. Riho
recommends that an inspection hatch should be placed near the overflow opening.
- Hot and cold water supply.
- Water drain
- Electrical connection, two groups of 230V/50Hz,
alternatively one group of 230V/50Hz. D epend on your
options. S ee chapter 1.5.6 for details.
- Potential difference equalisation 4- 6 mm² earth connection to whirlpool frame.
- Fixed connection to circuit-breaker with disconnection options (eg switch with status indication) .
Before installing the bathtub, pay attention to the following:
- Verify that the whirlpool is not damaged before installation. After installation, the warranty applies only to
hidden defects. The cost of dismantling the whirlpool will not be paid in case of defects found after installation.
- Do not use pipes, hoses or nozzles installed to handle tubs during transport and installation.
- Check the tightness of all connections on the bathtub before installation.
- The whirlpool must not touch the walls to prevent engine vibrations. Between the tub and the wall, it is
recommended to apply an insulating tape for noise reduction.
- When fixing the cover panels, take care of the height of the panel relative to the bottom edge of the bathtub.
Because of ventilation, the panel must be positioned at least 5 mm above the floor. In case of doubt, consult a
plumbing specialist or contact one of the RIHO assembly or service centers.
NOTICE:
Cover panels must be installed in such a way that the space under the bathtub meets ZONE 3 criteria, see
Chapter 1.1, ie. so that the space under the bathtub is not accessible without using the tool!
1.2 Whirlpool installation
All Riho Whirlpool baths are made of acrylic (see description: acrylic baths) and equipped with a Whirlpool system
of the customer's choice.
Please refer to the Riho price lists for details of all options.
1.3 Delivery
G enerally, all whirlpool systems are fully installed, functionally tested and packed.
ATTENTION:
Before installation remove the cardboard packaging and the foil to check the bath for damage, as well as material
and/or manufacturing defects. Protect the bathtub properly during installation (e.g. cardboard, blanket, bubble
foil, ...). After installation, RIHO can only give a guarantee on hidden material defects.
WARNING:
M
ake sure chrome parts don't come into contact with materials or water used to remove building materials, such
as mortar, grout or tile adhesive , because of possible chemical components in the composition which can
damage the chrome surface.
60cm
240cm
Zone 1
Zone 2
Zone 3
Zone 2
Zone 3
- 2 - - 3 -