Rigol RP1003C User Manual Download

Page: 4 / 33

RIGOL

RP1003C/1004C/1005C/1006C User Guide

General Safety Summary

CAUTION

This device is designed to comply with IEC 61010 Safety Standards, and has been

thoroughly tested for safety prior to shipment. However, mishandling during use

could result in injury or death, as well as damage to the device. Ensure that you

understand the instructions and precautions in the manual before use.

Safety Terms and Symbols

Before using the device, be sure to carefully read the following safety notes.

The

symbol printed on the device indicates that the

user should refer to a corresponding topic in the manual
(marked with the

symbol) before using the relevant

function.
In the manual, the

symbol indicates particularly

important information that the user should read before

using the device.

The

symbol printed on the device indicates that

only insulated conductors suited to the voltage of the

circuit under test can be measured.

The following symbols in this manual indicate the importance of cautions and

warnings.

DANGER

Indicates that incorrect operation presents an extreme

hazard that could result in serious injury or death to the

user.

WARNING

Indicates that incorrect operation presents a significant

hazard that could result in serious injury or death to the

user.

CAUTION

Indicates that incorrect operation presents a possibility

of injury to the user or damage to the device.

NOTE

Indicates advisory items related to performance or

correct operation of the device.

Summary of Contents for RP1003C


































Search results

Summary of Contents for RP1003C

Reviews:

Related manuals for RP1003C

Brands by name

Popular brands

Rigol RP1003C, User Manual

Search results

Summary of Contents for RP1003C

Reviews:

Related manuals for RP1003C

Brands by name

Popular brands