manualshive.com logo in svg

Rigol RP1003C, User Manual

Share
Download
Rigol RP1003C User Manual Download Page 16

RIGOL

 

6 

RP1003C/1004C/1005C/1006C User Guide 

To Use the Current Probe 

 

Before using the current probe, make sure to refer to 

Safety Precautions

. 

 

Preparations for Measurement 

 

1.

 

Prepare one RP1000P power supply and one waveform measurement 

instrument for waveform measurement. 

CAUTION

 

Before turning the power supply on, make sure that the voltage matches that 

indicated on the rear panel of the RP1000P. Connection to an improper supply 

voltage may damage the RP1000P and present an electrical hazard. 

 

2.

 

Turn the power switch off and connect the power cord. 

 

3.

 

Connect the power plug of the current probe to the power receptacle of the 

RP1000P.   

 

 

 

4.

 

Turn the RP1000P power switch on, and check that the front panel power 

indicator lights on. 

 

5.

 

Wait at least 30 minutes after turning on the current probe. Immediately after 

power is supplied, offset drift may increase due to the effects of self-heating of 

the device and other factors. To ensure accurate measurement, wait at least 30 

minutes after turning on the current probe before performing the 

measurement. 

 

 

Demagnetizing and Zero Adjustment 

 

1.

 

With the waveform measurement instrument input at ground, adjust the trace 

to the zero position. 

 

2.

 

Set the input coupling of the waveform measurement instrument to DC. 

 

3.

 

Connect the output connector of the current probe to the input connector of the 

Summary of Contents for RP1003C


































Reviews:

No comments

Brands by name

Popular brands

Load more brands