background image

 

 

RIGOL 

DS2000 Service Guide                                                                                    

Guaranty and Declaration 

 

Copyright

   

© 

2012 RIGOL Technologies, Inc. All Rights Reserved. 

 

Trademark Information 

RIGOL

 is a registered trademark of RIGOL Technologies, Inc.

 

 

Publication Number

 

SGA13101-1110 

 

Notices 

 

RIGOL

 products are protected by patent law in and outside of P.R.C. 

 

RIGOL

 reserves the right to modify or change parts of or all the specifications 

and pricing policies at company’s sole decision. 

 

Information in this publication replaces all previously corresponding material. 

 

RIGOL 

shall not be liable for losses caused by either incidental or consequential 

in connection with the furnishing, use or performance of this manual as well as 
any information contained.   

 

Any part of this document is forbidden to be copied or photocopied or rearranged 
without prior written approval of 

RIGOL

 

Product Certification 

RIGOL 

guarantees this product conforms to the national and industrial standards in 

China as well as the ISO9001:2008 standard and the ISO14001:2004 standard. Other 

international standard conformance certification is in progress. 

 

Contact Us 

If you have any problem or requirement when using our products or this manual, 

please contact 

RIGOL

E-mail: [email protected] 

Website: www.rigol.com 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for DS2000 Series

























Reviews: