Riello NetMan User Manual Download Page 4

ENGLISH 

INTRODUCTION 

Thank you for choosing our product. 
The accessories described in this manual are of the highest quality, carefully designed and 
built in order to ensure excellent performance. 
This manual contains detailed instructions on how to install and use the product. 
It should be kept with care near the device, so that it can be consulted for information on 
how to use and make the most of your device. 

IT SHOULD BE READ BEFORE YOU 

START WORKING ON THE DEVICE

 
 

SAFETY 

This part of the manual contains SAFETY precautions that must be followed 
scrupulously. 

The device has been designed to operate only in closed environments. It should be 
installed in rooms where there are no inflammable liquids, gas or other harmful 
substances. 
Take care that no water or liquids and/or foreign bodies fall into the device. 
In the event of a fault and/or impaired operation of the device, do not attempt to repair it 
but contact the authorized service centre. 
The device must be used exclusively for the purpose for which it was designed. Any other 
use is to be considered improper and as such dangerous. The manufacturer declines all 
responsibility for damage caused by improper, wrong and unreasonable use. 
 
© No part of this manual may be reproduced without the prior written permission of the 
manufacturer. 
The manufacturer reserves the right to modify the product described in this manual at any 
time and without notice. 

Summary of Contents for NetMan

























Reviews: