background image

17

USE

 

Warnings

The text “AttE” is displayed together with the alert number.

The equipment is not locked out, but its functions may be limit-

ed (according to the alert).

Contact your local Technical Assistance Service

2.2 

Temporary or short-term shut-down

In the event of temporary or short-term shut-down (e.g. due to 

holidays), proceed as follows:

 

− Remove the power supply by setting the main switch 

of the equipment and the main switch of the system to 

"OFF".

 

− If there is a danger of frost, keep the system on. To reduce 

fuel consumption, set the heating set point to the mini-

mum allowed value.

2.3 

Preparing for extended periods of disuse

If the appliance is not going to be used for a long period of time, 

the following operations should be carried out:

set the main switch of the system to OFF and the main switch of 

the equipment to (0);

 

− close the fuel cock and heating circuit water cock.

 

9

Drain the central heating circuit if there is any risk of freez-

ing.

2.4 

Device cleaning and maintenance

Please remember that THE PERSON RESPONSIBLE FOR SYSTEM MAN-

AGEMENT MUST ENSURE THAT PROFESSIONALLY QUALIFIED HEATING 

ENGINEERS UNDERTAKE PERIODIC MAINTENANCE AND COMBUSTION 

EFFICIENCY MEASUREMENTS.

R

’s Technical Assistance Service is qualified to satisfy these 

legal requirements and can also provide useful information on 

MAINTENANCE PROGRAMMES designed to guarantee:

 

− Greater safety

 

− Compliance with applicable legislation

 

− Freedom from the risk of fines in the event of spot checks.

Regular maintenance is essential for the safety, efficiency and 

durability of the boiler.

Servicing is a legal requirement and must be performed at least 

once a year by a professionally qualified heating engineer.

2.5 

External cleaning

Clean the boiler’s casing panels and control panel with a soft 

cloth damped in soapy water.

To remove marks from the boiler casing, use a cloth damped in a 

50% mix of water and denatured alcohol or a suitable cleaning 

product.

Wipe the boiler dry after cleaning it.

 

0

Do not use abrasive products, petrol or triethylene.

2.6 

Annual cleaning

At least once a year, the user must have the boiler served by 

R

's Technical Assistance Service or by a qualified heating en-

gineer.

Summary of Contents for INSIEME EVOe 32 B/110 LN





















Reviews: