background image

15 

20096985

GB

Installation

5.1

Notes on safety for the installation

After carefully cleaning all around the area where the burner is to
be installed, and arranging for the environment to be illuminated
correctly, proceed with the installation operations.

5.2

Instructions to avoid burnout or bad combustion of the burner

1

The burner can not  be  installed  outside as it  is suitable  for
operation in closed rooms only.

2

The  premises  the  burner  operates  in  must  have  openings
for the air need for the combustion. 
To  be sure  about  this,  you have to control  CO2 and CO in
the exhaust gases with all the windows and doors closed.

3

If there are air extractors in the premises the burner works,
make sure that there are openings for air to be taken in that

are  big  enough  to  ensure  the  required  air  change;  In  any
case,  check  that  when  the  burner  stops  the  extractors  do
not draw hot fumes from pipes through the burner.

4

When the burner is  stopped, the  smoke  pipe  must be  kept
open and a natural draft created in the combustion chamber. 
If the smoke pipe is closed, the burner must be drawn back
till the extraction of blast tube from the furnace. Before oper-
ating in this way take the voltage off.

5.3

Handling 

The transport weight is given in chapter “Technical data” on page
9
.

Observe the  permissible  ambient temperatures  for storage and
transport: -20 ..... + 70 °C, with max. relative humidity. 80%.

5.4

Preliminary checks

5.4.1

Control of the supply

5

Installation

DANGER

All the installation, maintenance and disassembly
operations must be carried out with the electricity
supply disconnected.

WARNING

The installation of the burner must be carried out
by qualified personnel, as indicated in this manual
and in compliance with the standards and regula-
tions of the laws in force.

DANGER

Combustion air inside the boiler must be free from
hazardous  mixes  (e.g.:  chloride,  fluoride,  halo-
gen); if present, it is highly recommended to carry
out cleaning and maintenance more frequently.

After  positioning  the  burner  near  the  installation
point, correctly dispose of all residual packaging,
separating the various types of material.

CAUTION

Before proceeding with the installation operations,
carefully clean all around the area where the burn-
er will be installed.

The  operator  must  use  the  required  equipment
during installation.

CAUTION

After removing all the packaging, check the integ-
rity of the contents. 

In the event of doubt, do not use the burner; con-
tact the supplier.

The  packaging  elements  (cardboard  box,  clips,
plastic bags, etc.) must not be abandoned as they
are potential sources of danger and pollution; they
should be collected and disposed of in the appro-
priate places.

Summary of Contents for Gulliver BS1/M





































Reviews: