manualshive.com logo in svg

RIDGID R4112, Operator'S Manual

Share
Download
RIDGID R4112 Operator'S Manual Download Page 35

35

ACCESSORIES

Look for these accessories where you purchased this product or call 1-866-539-1710:

  AC9945 Miter Saw Utility Vehicle .......................................................................................................................987310001
  Dust Bag Assembly ......................................................................................................................................089036008914
  10 in. Blade (40 Tooth) .................................................................................................................................089036008911
  Zero Clearance Throat Plate ........................................................................................................................089036008155
  Work Clamp .................................................................................................................................................089036008029
  Blade Wrench ...............................................................................................................................................089036008028

 

WARNING:

Current attachments and accessories available for use with this product are listed above. Do not use any attach-
ments or accessories not recommended by the manufacturer of this product. The use of attachments or acces-
sories not recommended can result in serious personal injury.

Summary of Contents for R4112






































Reviews:

No comments

Brands by name

Popular brands

Load more brands