Ricoh Rh 100 Operating Instructions Manual Download

Page: 23 / 26

Troubleshooting

Temperature and time settings will vary depending on the fabric used by the

•

customer (T-shirt, tote bag, etc.). Before configure the settings, wash with the
garment you use and check the fixability.

Problem

Cause

Solution

Ink does not fix
properly.

Appropriate temperature
is not set.

Change the temperature setting.
When you set a custom temperature, see
"Set Temperature and Time".

Ink does not fix
properly.

Appropriate time is not
set.

Change the time setting.
"Medium" (3 minutes) (Default setting)

"Long" (6 minutes)
When you set a custom time, see "Set
Temperature and Time".

Fabric color changes.

Appropriate temperature
is not set.

Change the temperature setting.
"High" (170 °C, 338°F) (Default setting)

"Low" (150 °C, 302°F)
When you set a custom temperature, see
"Set Temperature and Time".

Fabric color changes.

Appropriate time is not
set.

Change the time setting.
"Medium" (3 minutes) (Default setting)

"Short" (1 minute)
When you set a custom time, see "Set
Temperature and Time".

Fabric color changes.

The heater and the fabric
might be in contact with
each other during fixing
processing.

Before setting the fabric, attach the spacers
included in the cassette on the four sides
of the inside of the cassette. It is possible to
prevent the heater and the fabric from com-
ing into contact during fixing processing.

DSA545

Summary of Contents for Rh 100



























Search results

Summary of Contents for Rh 100

Reviews:

Related manuals for Rh 100

Brands by name

Popular brands

Ricoh Rh 100, Operating Instructions Manual

Search results

Summary of Contents for Rh 100

Reviews:

Related manuals for Rh 100

Brands by name

Popular brands