Ricoh PJ S2130 User Manual Download

Page: 3 / 54

English

Usage Notice

Precautions

Follow all warnings, precautions and maintenance as recom-

mended in this user’s guide to maximize the life of your unit.

■

Warning-

This apparatus must be earthed.

■

Warning-

Do not look into the projector’s lens when the

lamp is on. The bright light may hurt your eyes.

■

Warning-

To reduce the risk of fire or electric shock, do not

expose this projector to rain or moisture.

■

Warning-

Please do not open or disassemble the projector

as this may cause electric shock.

■

Warning-

When replacing the lamp, please allow unit to

cool down, and follow all replacement instruc

tions..

■

Warning-

This projector will detect the life of the lamp

itself. Please be sure to change the lamp when it

shows warning messages.

■

Warning-

When switching the projector off, please ensure

the cooling cycle has been completed before

disconnecting power. Allow 60 seconds for the

projector to cool down.

■

Warning-

Do not use lens cap when projector is powered

on.

■

Warning-

Turn on the projector first and then the signal

sources.

■

Warning-

When the lamp reaches the end of its life, it will

burn out and may make a loud popping sound.

If this happens, the projector will not turn back

on until the lamp module has been replaced. To

replace the lamp, follow the procedures listed

under “Replacing the Lamp”.

■

Warning-

Do not remove the cabinet cover, or you may be

exposed to dangerous voltage. Refer servicing to

qualified service personnel only.

Summary of Contents for PJ S2130























































Search results

Summary of Contents for PJ S2130

Reviews:

Related manuals for PJ S2130

Brands by name

Popular brands

Ricoh PJ S2130, User Manual

Search results

Summary of Contents for PJ S2130

Reviews:

Related manuals for PJ S2130

Brands by name

Popular brands