Ricoh InfoPrint XT, Installation And User Manual

Page: 157 / 202

AIOxxx491E The transform detected an attempt to
reshape graphic characters by using
nongraphic Xerox font font_name on page
page_number , logical record line_number .
Of number active fonts, font_name is
number number and no graphic fonts
were found in the active font list.
AIOxxx491E The transform detected an attempt to
reshape graphic characters by using
nongraphic Xerox font font_name on page
page_number
, logical record
line_number
.
Of number active fonts, font_name is
number number . Active graphic fonts
include graphic_font1 (number a),
graphic_font2 (number b), and
graphic_font3 (number c).
Explanation: InfoPrint XT found a character-shaping
metacode print control sequence that specified a
nongraphic font. The message either indicates that no
graphic fonts were active, or lists up to three active
graphic fonts.
System action: Processing continues, but graphics
might be missing from the output.
User response:
Compare the font list in effect with the
font list expected at metacode generation. Correct the
inconsistency between the font lists and rerun the job.
AIOxxx492E A translation error occurred while
processing input character x’ input_hex ’ at
logical record line_number . Code page
code_page did not contain EBCDIC
character x’ EBCDIC_hex ’. The transform
substituted a blank. The original Xerox
font was font_name .
Explanation:
While processing metacode print
controls, InfoPrint XT translated ASCII input character
x’ input_hex ’ to EBCDIC character x’ EBCDIC_hex ’.
However, because this character is not available in code
page code_page , InfoPrint XT uses a blank in its place.
This might occur because of incorrect characters, such
as binary zeros, in the print data stream. It might also
occur if you have manually correlated a Xerox font to
an AFP font, and the AFP font does not have characters
that correspond to some of the characters in the Xerox
font.
System action: InfoPrint XT continues processing the
job, but the output is not correct.
User response:
Correct the input data or correlation,
and rerun the job.
AIOxxx493E The data stream converter found no font
information for AFP DBCS coded font
font_name . Characters will print as
blanks.
Explanation: InfoPrint XT did not process DBCS
information for font_name .
System action: InfoPrint XT continues processing the
job, but the output is not correct.
User response: Reload the corresponding Xerox font
to make sure that the information is available.
AIOxxx500S The data stream converter could not
find the image correlation table in the
reformatted Xerox resource path, or the
table contains no entries.
Explanation: InfoPrint XT requires a Xerox image
(IMG) to process the job, but no image correlation
records exist in the correlation table. Typically, this is
because no IMG resources were loaded, or they were
loaded as non-shared resources for a different resource
group.
System action: The process fails.
User response:
Load the required resource as a shared
resource or load it in the correct resource group for the
job, and rerun the job. If the problem continues after
you load the image, report this message to your
technical support representative.
AIOxxx550W The data stream converter ignored a
DJDE identifier on record line_number:
djde_record .
Explanation: InfoPrint XT ignored the DJDE record
djde_record , which it considers to be extraneous. If the
DJDE record was a downloadable PDE (FORMAT=*),
djde_record contains a message that indicates that
InfoPrint XT did not use the fonts listed in the
downloadable PDE.
System action: InfoPrint XT continues processing the
job.
User response: Check the input data stream for any
occurrence of consecutive DJDE packets (one or more
DJDEs ending with an END;) with no intervening data
records. Correct the problem and rerun the job.
AIOxxx562W The data stream converter found a
conflicting COLLATE change request.
Explanation:
The data stream specified
COLLATE=NO, but also specified DUPLEX=YES,
which implies COLLATE=YES.
System action: InfoPrint XT processes the data stream
using COLLATE=YES.
User response: Make sure of the correct placement of
Appendix D. Resource utility messages and data stream converter messages: AIO xxxnnnx
137
|
|
|